D2/D5 CNC brochure

Product catalog summary

Introduction
The document describes the escomatic D2/D5 CNC machines, highlighting their unique design and operational advantages over conventional lathes. These machines are designed for high productivity and flexibility in manufacturing small, medium, and large lot sizes of simple parts.

Escomatic Concept
Unlike traditional lathes, escomatic lathes use a stationary material with rotating cutting tools. This design allows for efficient manufacturing and cost savings. The material is fed from a coil, straightened, and then machined with high precision.

Material Handling
The material is fed into the machine from a coil, straightened to bar stock quality, and clamped by grooved rollers for precise feeding. This setup allows machining of very small wire diameters without deformation.

Turning Process
The escomatic principle involves rotating cutting tools around the material at speeds up to 12,000 rpm. The counter collet ensures flatness and a clean cut-off.

Machine Variants
The D2 CNC is designed for high-speed production of parts up to 4.0 mm in diameter. The D5 CNC includes additional frontal machining capabilities with a cross table supporting drilling and threading spindles.

Technical Features

Maximum part diameter: 4 mm
Tool head speed: up to 12,000 rpm
Material feed rate: 8 m/min
Drilling speed: up to 18,000 rpm
Compact design for space efficiency
Easy setup and operation without cams

Operational Advantages
The machines offer flexible programming, reduced labor costs, and improved part quality. They are suitable for 24-hour production with minimal machine stops.

Technical Data

Installed power: 4 kVA
Dimensions: 1350 x 770 x 1380 mm
Net weight: 850 kg

Conclusion
The escomatic D2/D5 CNC machines provide a cost-effective solution for high-precision manufacturing with enhanced productivity and flexibility.

Catalog excerpts

tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:8.00pt "Arial", sans-serif; } .font1 { font:11.00pt "Arial", sans-serif; } .font2 { font:18.00pt "Arial", sans-serif; } .font3 { font:20.40pt "Arial", sans-serif; } .font4 { font:21.00pt "Arial", sans-serif; } .font5 { font:26.00pt "Impact", sans-serif; } .font6 { font:42.00pt "Impact", sans-serif; } TOURS AUTOMATIQUES se D2/D5 cnc scomatk 22,5PCS/MIN productivity of the cams and flexibility of the cnc www.escomatic.ch

Open the catalog to page 1

tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:4.80pt "Arial", sans-serif; } .font1 { font:6.00pt "Arial", sans-serif; } .font2 { font:8.00pt "Arial", sans-serif; } .font3 { font:10.00pt "Arial", sans-serif; } .font4 { font:19.00pt "Arial", sans-serif; } .font5 { font:21.00pt "Arial", sans-serif; } .font6 { font:9.00pt "Microsoft Sans Serif", sans-serif; } Unlike conventional lathes, escomatic lathes are based on a unique concept. The material, which is coil stock or bar, does not rotate. The cutting tools mounted onto the spinning tool head rotate around the material. This...

Open the catalog to page 2

tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:8.00pt "Arial", sans-serif; } .font1 { font:18.00pt "Arial", sans-serif; } .font2 { font:21.00pt "Arial", sans-serif; } .font3 { font:25.00pt "Arial", sans-serif; } .font4 { font:19.00pt "Tahoma", sans-serif; } .font5 { font:14.00pt "Trebuchet MS", sans-serif; } escomatic D2/D5 CNC: 3 MATERIAL FEED The material is supplied into the machine from coil. A coil, depending on the type of material, usually has 30 to 50 kg and is unrolled from a reel supported by the machine. The material is pulled across the machine by the material feed...

Open the catalog to page 3

tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:8.00pt "Arial", sans-serif; } .font1 { font:10.00pt "Arial", sans-serif; } .font2 { font:18.00pt "Arial", sans-serif; } .font3 { font:25.00pt "Arial", sans-serif; } .font4 { font:4.00pt "Impact", sans-serif; } .font5 { font:6.00pt "Impact", sans-serif; } .font6 { font:8.00pt "Impact", sans-serif; } escomatic D2/D5 CNC: 4 TECHNICAL DATA Turning: Maximum part diameter Maximum workpiece lenght Number of cutting tools Max. tool head speed Material feed rate (Z1) Straightening: D2 Sraightening unit Straightening length Straightening...

Open the catalog to page 4

All ESCO S.A. catalogs and technical brochures

NM6 Flexi
2 Pages

D2/D5 CNC brochure

D2/D5 CNC brochure

Catalog excerpts

All ESCO S.A. catalogs and technical brochures

Archived catalogs