Handle for receiving various adapter blocks for performing adhesion tests VarioCut 404 with all accessories testing equipment for quality management Technical Description and Instruction EN EN ISO Standardized defined

Safety Instructions Proper Use The Model 404 is used to perform adhesion tests by scratch and cross-cut tests in accordance with international standards and for standardized defined preparation of samples for corrosion tests. This instrument is a purely mechanical instrument. The new VarioCut 404 enables the user to employ a useful number of needed test tools, to have provided without every one of them with its own handle/holder and storage case. The complete retrofittable accessory takes place here! Risk of Injuries! The blades and the test tips to use with the various adapters, are very sharp...

In the basic version the VarioCut 404 is supplied with grip, chuck adapter, steel ruler and plastic case. Optionally, a total number of five different adapters with various suitable tools are available: - Clamping chuck adapter (including in the scope of supply) To attach test tools with shaft diameter up to 4 mm (optional), as - Adapter block „Sikkens“ (in about 45° beveled positioning) to attach Sikkens cutting tools for producing a cutting trace with a rectangular edged channel, for application of defined scratches for corrosion tests - Cutting edge made of hard metal (0.5 mm) - Cutting edge...

During the corrosion tests the specimens are scored with a scratching tool at the beginning and at periodic intervals. The scratches will be made from the bottom up horizontally above each other and parallel to the narrow side of the sample. By this mode of operation, the progressive subsurface corrosion can be observed very well. To reach the ground safely and to achieve a slight deformation of the metal, more or less force will required in the application, depending on the thickness and hardness of the paint layer. It is expedient to use a ruler to achieving a clear & straight scratch. The...

Order Information Figures Multifunctional Handle VarioCut 404 Adaptable anti-slip grip made of aluminium with engraved grid pattern, with freely rotating as well as locked axis for constant force application. incl. - clamping chuck adapter to attach the cross-cut single edge, the corrosion scratch tools acc. to van Laar and Clemen as well as many userspecific tools with shaft diameter up to 4 mm - flexible steel ruler - plastic case (without test tip) Necessary Accessories (at option): Test tip for cross hatch cutting (30°), additionally covered with an extremly hard layer Addionally accessories...

Order Information Figures Adapter block 45° In about 45° beveled positioning, without laterial levelling wheel or other levelling degree for flexible working on anti-plane geometry parameters; to attach the test tip for cross hatch cutting, the corrosion test tips acc. van Laar and Clemen as well as many user-specific tools with shank diameter up to 4 mm (without test tips) Necessary Accessories (at option): 0539.01.32 Test tip for cross hatch cutting (30°), additionally covered with an extremly hard layer Cross Cutter Adapter to attach multi cross cutter for the cross-cut test, incl. polyamide...

Order Information Figure Single Edge Cutter Cutter with 2 edges, cutting distance 5 mm Cutter with 11 edges, cutting distance 1 mm Cutter with 6 edges, cutting distance 3 mm Chucking adapter (rolling) for fixing and vertical guidance of the ERICHSEN hardness test pencil Model 318, in standard version as well as with test head “C” and test tip “Clemen” – without hardness test pencil Hardness Test Pencil, Model 318 incl. test tip no. 1 (acc. to Bosch; 0,75 mm Ø) and 3 springs Further accessories for Model 318: 2109.01.32 Test head „C“ (movable/retrofit) for models 318/318 S, for clamping the Clemen...

The right of technical modifications is reserved. Group 12 - TBE/BAE 404 - II/2015 Postfach 1264 I 58652 Hemer I Germany I Tel. +49(0)2372-9683-0 I Fax+49(0)2372-6430 I www.erichsen.de I [email protected]