Compliant with ITU-T G.987.2 N1 Class Single fiber bi-directional Transceiver 2.488Gbps upstream and 9.953Gbps downstream RoHS6 Compliant Features ♦ XFP MSA package with SC receptacle optical interface ♦ 9.953 Gbps/1577 nm Continuous Mode Transmitter with EML laser 2.488Gbp/1270nm High Sensitivity Burst-Mode APD-TIA Receiver Supports Digital Diagnostic Monito Functions Burst mode received signal strength indication (RSSI) output LVCML interface logic level for 2.488Gbps data output LVCML interface logic level for y ♦ Operating Case Temperature Standard:0°C~+70°C Industrial: -40C~+85C ♦ Compliant with Class 1 FDA and IEC60825-1 laser safety Applications ♦ XG-PON N1 Class *The Product image only for reference purpose Eoptolink Technology Inc., Ltd. Page 1 of 10

*Exceeding any one of these values may destroy the device permanently. Eoptolink Technology Inc., Ltd. Page 2 of 10

10G PON Series _PreliminaryRecommended Operating Conditions Parameter Eoptolink Technology Inc., Ltd. Page 3 of 10

Note1:Measured with a PRBS 223-1 test pattern @2.488Gbps and ER=8.2, BER=10-4 Eoptolink Technology Inc., Ltd. Page 4 of 10

10G PON Series _PreliminaryXFP Transceiver Electrical Pad Layout GND I Toward BEZEL )iagram of Host Board Connector Block Pin Numbers Below figure shows the pin information of electrical interface and mounting studs. Functions are described in the following table. Eoptolink Technology Inc., Ltd. Page 5 of 10

Optical Input Signal RSSI_TRI Trigger Input Signal Eoptolink Technology Inc., Ltd. Page 6 of 10

Eoptolink’s EOLX-PX-GT-30 Small Form Factor 10Gbps (XFP) transceivers are compliant with the current XFP Multi-Source Agreement (MSA) Specification Rev 4.5. As defined by the XFP MSA, Eoptolink XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: ♦ Transceiver temperature ♦ Laser bias current ♦ Transmitted optical power ♦ Received optical power ♦ Transceiver supply voltage The structure of the memory map is shown in the following figure, which is accessible over a 2-wire serial interface at the...

10G PON _Preliminary EEPROM Serial ID Memory Contents Accessing Serial ID Memory uses the 2 wire serial address 1010000X (A0H). Memory Contents of Serial ID are shown in Table 1. Table 1 Serial ID Memory Contents Eoptolink Technology Inc., Ltd. Page 8 of 10

Recommended High-Speed Interface Circuit Mechanical Specifications *This 2D Drawing only for reference, please check with Eoptolink before ordering Eye Safety This single-mode transceiver is a Class 1 laser product. It complies with IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. Eoptolink Technology Inc., Ltd. Page 9 of 10

10G PON Series _Preliminary Obtaining Document You can visit our website:http://www.eoptolink.com Or contact Eoptolink Technology Inc., Ltd. listed at the end of the documentation to get the latest document. Notice: Eoptolink reserves the right to make changes to or discontinue any optical link product or service identified in this publication, without notice, in order to improve design and/or performance. Applications that are described herein for any of the optical link products are for illustrative purposes only. Eoptolink makes no representation or warranty that such applications will be...