Easylock ELID-x-138

Product catalog summary

Technical Features
The Easylock ELID-x-138 clamping module is designed for precise positioning and clamping of workpieces or fixtures, achieving a repeat accuracy of less than 5 μm. The system uses clamping slides to lock pins in place, with a pneumatic unclamping mechanism operating at 6 bars. Optional features include a blow-out system (-S), unlocking control system (-C), and indexing system (-I).

Clamping Pin Models
Three clamping pin models are available: TELD (Centering Pin), TCELD (Positioning Pin), and TDELD (Pull-stud Pin). The Easylock devices can be configured with one to three female couplers (ELID-1-138, ELID-2-138, ELID-3-138), which can be supplied as extras.

Specifications

Pneumatic operation with a repeat accuracy of 0.005 mm.
Operating pressure for opening is 6 bars, with a maximum pressure of 10 bars.
Pull-in force ranges from 35 kN to 50 kN depending on the model (CHc M10/CHc M12).
Axial clamping force is 5 kN.
Weight with set screws is 4.4 kg.

Dimensions and Mounting
The system includes options for pneumatic blow-out to loosen clamping pins, with mandatory blow-out holes. It can be mounted built-in, semi-recessed, or on the surface. The blow-out option requires a minimum pressure of 6 bars and a maximum of 10 bars.

Clamping Pin Accessories
Accessories for clamping pins include options for ELID-0-138 (-S), ELID-1-138, ELID-2-138, and ELID-3-138. Clamping pins can be attached using an M12 screw from below or a CHc M10 screw from above, with a clearance hole for the CHc M10 screw.

Installation and Positioning
Installation involves housing for an alignment bore ø2, with specific models for centering (TCELD), positioning (TDELD), and pull-stud (TELD) pins.

Catalog excerpts

EASYLOCK WITH CLAMPING SLIDES ELID-x-138 (-S)(-I) Technical Features The Easylock ELID-x-138 clamping module positions and clamps workpieces or fixtures with a repeat accuracy of less than 5 μm. The pins are locked by the clamping slides inside the EASYLOCK. EASYLOCK system locks the clamping pins in rest position. A safety system guarantee. Unclamping is pneumatic at 6 bars. The EASYLOCK can be equipped with a blow-out system (-S), an unlocking control system (-C), or an indexing system (-I). Our three respective clamping pin models: TELD: Centering Pin TCELD: Positioning Pin TDELD: Pull-stud Pin For pallets or base plates with hydraulic and/or pneumatic clamping fixtures on, our Easylock devices are available as follows: ELID - 1 - 138: Easylock with 1 female coupler ELID - 2 - 138: Easylock with 2 female couplers ELID - 3 - 138: Easylock with 3 female couplers The female couplers can be supplied as an extra. For clamping pins, see pages 36 and 37 P. 34 / EASYLOCK

Open the catalog to page 1

EASYLOCK pneumatic blow-out for loosening the clamping pin 08.5x1.8 o-ring DIMENSIONS AND MOUNTING POSSIBILITIES blow-out output on the surface blow-out (option) blow-out option mandatory blowing out hole Technical Features minimum pressure 6 bars maximum pressure 10 bars Repeat accuracy Operating pressure for opening 6 bars Maximum pressure built-in mandatory blowing out hole Axial clamping force Weight with set screws mandatory blowing out hole

Open the catalog to page 2

FOR EASYLOCK WITH Ø138 CLAMPING SLIDES CHc M10 screw clearance hole TxELD clamping pin catalogue 2 WAYS TO SCREW THE CLAMPING PINS : Attachement of an M12 screw frome below or Crossing using a CHc M10 screw from above. 10x45 screw Housing for an alignment bore ø2

Open the catalog to page 3