Pallet Components Valves f Power Sources Linear Cylinders Work Supports Swing clamps ( Collet-Lok® products (0 Accumulator packages will help maintain system pressure to your fixture when separated from the hydraulic source. The gauge will display system pressure after the circuit is disconnected. Coupler packages ...compact design for easy use of accumulators • Single design accommodates both single-acting or double-acting circuit • Relief valve fitted and ball check shut-off • Glycerin-filled gauge included • Supplied standard with one male coupler (AH-652) • Optional manifold mounting. O-ring seals located on bottom of block only for single-acting circuit. MHV-1 Modular holding valve • Allows separate operation of clamping fixtures with a single power source • Ideal for applications when fluid feed lines are impractical. If system pressure is interrupted, the MHV-1 will hold the pressure beyond the valve • Max. oil flow 5 l/min • To release system pressure, rotate valve handle in either direction 90° to release and retract system pressure. 0 Coupler package circuits ACBS Single-acting circuit Double-acting circuit RA ] OKZ) Q Product selection Max. rated oil volume Gas Pre-charged volume nitrogen pressure 11 See pre-charge chart on page 163 for hydraulic operating pressures.

Dimensions & options AC, AP, MHV-serieS Pressure: 0 - 350 bar Oil volume: 16,4 -163,9 cm3 Gas volume: 20 - 169,9 cm3 vJT) Acopladores manuales vF^) Manuel coupleur D Manuelle kupplung Enerpac high pressure in-line filters are required for use with these control units to prevent damage that can be caused by contaminants that have penetrated your hydraulic fluid system. Order an additional male coupler for use in doubleacting hydraulic circuits. ACBS-Series: AH-652 AP-500: AH-654 © Product dimensions in mm [ ^ ] Model number Recommended charging tool Pallet Components System Components Yellow...

Manual Couplers Application & selection Collet-Lok® products Manual Couplers …convenient connection • Use on palletized fixtures • vailable with or without an internal pilot operated (P.O.) A check valve Swing clamps • ptional coupler block available to add circuit for air O part present sensing • Manifold porting • Porting for tubing connections Linear Cylinders Work Supports • Filtration to prevent contamination R • emovable front plate provides access to the front filters and check cartridge The Enerpac manual coupler is available as a dual connection model or dual connection with optional...

© Select your components MCRC-21 Pallet Receiver with P.O. Check An internal pilot operated check valve and multiple ports to accommodate a gauge or accumulator make the MCRC-21 a great choice of coupler receiver for use in a palletized fixture. Internal filtration protects the check from contamination. Use with the MCH-21 operator handle. MCR-21 Pallet Receiver For applications where the pilot operated check valve is remote mounted in the fixture circuit, use the MCR-1. Internal filtration protects the circuit from outside contamination. MCRA-11 Auxiliary air circuit receiver The MCRA-11 is...

Manual Couplers Dimensions & options Collet-Lok® products Receiver with pilot operated (P.O.) check The Enerpac MCH-21 two passage operator handle conveniently connects and disconnects to the MCR-21 two passage receiver utilizing a simple push-on, pull-off action. Receiver without pilot operated check ø 4,8 mm 15,7 mm length spring roll pin (included) 5/16"–18UN 38 mm length Socket Head Cap Screw (included) Power Sources Linear Cylinders Work Supports Swing clamps See page 170 for mounting pattern. Auxiliary air circuit receiver 2x #10-24 UN 38 mm length Socket Head Cap Screw (included) Pallet...

Dimensions & options MCRC-21 with MCRA-11 MCR and MCH-series Max. Flow: 15 l/min See page 170 for mounting pattern. (3x) 5/16"–18UN, 38 mm length Socket Head Cap Screw (included) 2x #10-24 UN, 38 mm length Socket Head Cap Screw (included) Pressure: 0 - 350 bar E Acopladores manuales F Manuel coupleur D Manuelle kupplung Options Can mount air passage on either side Storage block. See page 171 for mounting pattern. 2x 1/4"-20UN 13 mm length Socket Head Cap Screw (included) 2x M5x4,8 20 mm length Socket Head Cap Screw with jam nuts (included) Optional proximity switch 192 ▸ Pilot operated check...

Manual Couplers Mounting patterns Collet-Lok® products MCRC-21 Receiver with P.O. check – Receiver without P.O. check – Mounting hole pattern Mounting hole pattern Swing clamps * Minimum from edge of tool plate 100,0 * Work Supports Linear Cylinders The MCR-21 two passage receiver features multiple SAE #4 ports as well as manifold mount ports for easy plumbing to a fixture. Internal filtration in all receiver models protects the circuit from external contamination. Receiver with air passage and with P.O check – Mtg. hole pattern Power Sources Can mount air passage on either side. feed hole *...

Mounting patterns, dimensions & options MCSB-21 Storage Block – Mounting Hole Pattern 1/4”-20UNC 12,7 mm length drill ø 5,2 mm, 16 mm deep 19,1 E Acopladores manuales F Manuel coupleur Manifold and Port Dimensions 1/16"-27 NPTF dry seal taper pipe plugs. Remove when manifold mounting. 1/16"-27 NPTF dry seal taper pipe plugs (2x). Remove when manifold mounting. Options FZ Series fittings 194 ▸ O-ring (included). Use when manifold mounting. feed holes (2x) O-ring (included). Use when manifold mounting. feed holes (2x) Rear view 192 ▸ Pilot operated check valves Port passages SAE #4 plugs (6x) included....

Pallet Components j Valves f Power Sources Linear Cylinders Work Supports Swing clamps ( Collet-Lok® products Auto-coupler systems Application & selection For automated coupling of hydraulic circuits on palletized systems • Sensing feedback of coupler position allows for fully automated applications • Horizontal or vertical mounting for flexible installation on machine tools • Available as 2 or 4 port model to provide a solution to various hydraulic circuit needs • Adjustment stroke allows clearance for pallet indexing • Coupler elements supplied with air blow-off nozzles to prevent...