Catalog excerpts
The new slim 19-inch EMC chassis with an overall height of 1 U 2. Ecokit 11 The economic way to build up a simple card cage in different variants 3. Magic- /Spirit-Kit 11 EMC sub rack in sheet steel with a very fast assembly and EMC without gaskets 4. Systemkit 12K Modern designed EMC sub rack with a large selection of assembly options 5. Systemkit 12K Rail Sub rack solutions for demanding railway applications Elmaset Elmaset
Open the catalog to page 41.2.1 Slimkit 10 Basic Tray Front view 1.4.1 Line Drawings for Slimkit 10 1.4.2 Assembly SHEETtracs® Screw Plan view
Open the catalog to page 619“ EMC chassis 1 U Basic model can be transformed into a complete case by adding a rear panel, top cover as well as a mounting chassis Design allows numerous combinations to be assembled according to the application Hard and wear resistant aluminium front panel With or without perforations for optimised thermal solution EMC-Slimkit 10 can be presented in a number of attractive finishes for individual product tailoring Technical features • 19“ chassis with excellent EMC feature • Front panel: aluminium, frame construction: sheet steel, pre-galvanised • Vibration-proof • EMC shielding...
Open the catalog to page 7Elma’s EMC concept describes three levels of electromagnetic shielding performance (Performance Level). The attenuation levels will simplify the selection of sub racks for the user. Test setup: The first measurement E1 is without the enclosure. The next measurement E2 is made with the transmitting antenna installed inside the enclosure. The difference between the received signal without and with the enclosure represents the shielding effectiveness in dB. Performance Level 1 / Elma: Basic level 2 / Elma: Advanced level 3 / Elma: Superior level The standard configuration will provide you with...
Open the catalog to page 81 : Slimkit 1 0 Configuration - 1 U - 240 mm / 360 mm - Solid / perforated - With / without handles - Different colours - Earthing Kit - Case feet
Open the catalog to page 91.2 Slimkit 10 EMC Chassis 1.2.1 Slimkit 10 Basic Tray • 0.75 mm sheet steel, pre-galvanised • With holes for fastening of mounting chassis, feet, earthing terminals, front / rear panel, top cover • Scope of delivery: • Basic Tray • Assembly material for mounting front panel, rear panel, mounting chassis, top cover (12 round head SHEETtracs® screws 3,0 x 6, Torx T10) • Front Panel see 1.2.2 • Rear Panel see 1.2.3 • Top Cover see 1.2.4 • Mounting Chassis see 1.2.5 1.2.1 Slimkit 10 Basic Tray
Open the catalog to page 10• Rear: conductive, front: clear anodised / powder coated black (RAL 9005) / powder coated light grey (RAL 7035) • With or without black handles • Customised front panel upon request (see front panel service) • Scope of delivery: • Front panel • Handle set (2 black U-handles, 4 countersunk screws M2.5 x 8, Torx T8) in handle versions only • Assembly material for mounting front panel included in basic tray set
Open the catalog to page 11• 0.75 mm sheet steel, pre-galvanised • With or without air perforation • Scope of delivery: • Top cover • Assembly material for mounting top cover included in basic tray set
Open the catalog to page 121: Slimkit 101.3 Accessories 1.3.1 Earthing Set • Enables cases to be earthed in conformance with EN / VDE / SEV • Scope of delivery: • 1 press-in threaded bolt M4 • 2 serrated lock washers • 2 hexagonal nuts M4 • 1 terminal clamp • 1 earthing symbol Serrated lock washer Earthing terminal symbol Clamp strap Serrated lock washer Hexagonal nut 1.3.2 Case Feet Tilt foot / Non-tilt foot Choice of colours: light grey (RAL 7035) or black (RAL 9005) Glass-fiber reinforced plastic, UL94 V-0 Up to 30 kg carrying capacity per set Scope of delivery: • 1 set of feet • Assembly material (8 cross...
Open the catalog to page 131: Slim kit 1 0 1.4 Technical Information 1.4.1 Line Drawings for Slimkit 10 Side view Mounting chassis Plan view Plan view Plan view SideSide view view Front view Front view Front view 1.4.2 Assembly SHEETtracs® Screw • For a secure thin sheet metal joint with pre-hole 1.4.2 SHEETtracs® Screw Description 3 x 6, Torx T10 Material Steel, zinc-plated 1. Initial position Elmaset
Open the catalog to page 14A | 2_3 2.2 Ecokit 11 Sub Rack Configuration A | 2_5 2.3.2 Front Sub Division Horizontal IEC for Card Guides A | 2_9 2.3.3 Front Sub Division Horizontal IEC A | 2_9 2.3.4 Edge Connector Extrusion 66-145 A | 2_10 2.3.5 Edge Connector Extrusion 66-147 A | 2_10 2.4.1 Front Sub Division Vertical 6 U / 3 U A | 2_11 2.4.2 Horizontal Card Mounting Kit A | 2_12
Open the catalog to page 152.5.1 Perforated Cover Plates 2.5.4 Flat Front Panels 2.5.5 Fan Front Panel for Horizontal Ventilation 2.5.6 Fan Front Panels for Direct Fan Mounting 2.5.7 Extruded Front Panels 2.5.8 Front Panel with Cutouts for IEC Ejector Handles 2.5.9 Ergonomic Ejector Handles acc. to IEC 2.5.10 Card Locks and Card Handles 2.5.11 Card Holder acc. to IEC Standard 2.5.13 Protective Cover for 6 U Printed Board 2.5.16 Hexagonal Spacers M3 Thread 2.6.5 Edge Connector Extrusions
Open the catalog to page 16Side panels are of 2 mm sheet aluminium The extruded aluminium 19" mounting sections have an effective thickness of 3 mm (Standard only) For mounting PCBs and plug-in units based on standard Eurocard sizes with depths of 160, 220 and 280 mm The use of cover plates is recommended where the sub rack is subjected to continuous vibration Side panel with integrated 19" section as a cost-saving solution for Ecokit 11 Integrated Features on the side panels allows the extrusions to be fixed with only half the number of screws Assembly example: Ecokit 11 Integrated Internal extrusion Internal...
Open the catalog to page 172: Ecokit 1 1 Configuration - 42 HP / 84 HP (incl. assembly material)) - 3 U / 6 U - With / without holes for handles - Standard / integrated - 216 mm / 336 mm 2.2.3 Handles 2.3 Adaptation Kits
Open the catalog to page 182: Ecokit 11 2.2 Ecokit 11 Sub Rack Configuration 2.2.1 Width • Choose the width of your sub rack • Set with or without centre extrusion • Scope of delivery: • 2 front extrusions, aluminium, clear anodised • 4 tapped strips M2.5 (6 for version with centre extrusion) • 2 internal extrusions • 1 centre extrusion (version with centre extrusion only) • Insulating strips (Backplane mounting only) • Assembly material (Torx screws) • Label strips see below • Choose the right height and depth on the next step (see 2.2.2) Other widths available on request 2.2.1.1 Label Strips • Scope of delivery: •...
Open the catalog to page 19All Elma Electronic AG catalogs and technical brochures
-
Compact Case 20 Datasheet
4 Pages
-
Banana Socket_Datasheet_E
2 Pages
-
Artificial Intelligence
4 Pages
-
The Elma OpenVPX ecosystem
4 Pages
-
Unibox 14_Datasheet_E
19 Pages
-
Systemkit 12K_Datasheet_E
25 Pages
-
Stylebox 15 e-motion_Datasheet_E
32 Pages
-
Elma RS Catalog_E
194 Pages
-
E33 Encoder_Datasheet_E
9 Pages
-
E37 Encoder_Datasheet_E
7 Pages
-
07_C07A Coded Switch_Datasheet_E
10 Pages
-
C07 Concentric_Datasheet_E
6 Pages
-
Classic Collet Knobs_Datasheet_E
11 Pages
-
LED_Datasheet_E
6 Pages
-
Elos Box 54_Datasheet_E
2 Pages
-
Guardbox 33_Datasheet_E
16 Pages
-
Varietybox 35_Datasheet_E
10 Pages
-
Guardbox 33 easy_Datasheet_E
5 Pages
-
iD-Box 16_Datasheet_E
2 Pages
-
Ecokit 11_Datasheet_E
9 Pages
-
Slimkit 10_Datasheet_E
6 Pages
-
C15 Coded Switch_Datasheet_E
3 Pages
-
E18 Encoder_Datasheet_E
7 Pages
-
Railway
32 Pages
-
Corporate Overview
12 Pages
-
Front Panel Printing Methods
1 Pages
-
iD-Box 16_Datasheet_E
2 Pages
-
Slimkit 10 FTTx_Datasheet_E
1 Pages
-
K1 Metal Knobs_Datasheet_E
3 Pages
-
M07 Coded Switch_Datasheet_E
5 Pages
-
C16 Coded Switch_Datasheet_E
3 Pages
-
C08 Coded Switch_Datasheet_E
6 Pages
-
Brochure iD-Box 16_E
8 Pages
-
Brochure BT Box 24_E
4 Pages
-
Brochure Shapebox 22_E
4 Pages
-
Subrack 38_Brochure_E
6 Pages
-
12R2 Rugged Chassis
2 Pages
-
Rotary Switches Brochure
4 Pages
-
19" Frontpanels
2 Pages
-
Power Supplies
8 Pages
-
ELOS Elma Open System
4 Pages
-
Elma bustronic
68 Pages
-
Optima stantron
80 Pages
-
PICMG
136 Pages
-
Optima stantron
25 Pages
-
PRESENTATION RACKS
1 Pages
-
Pioneer Standard
5 Pages
-
VITA Type 12 Chassis Platforms
32 Pages
-
Customisation_and_Services_E
16 Pages
-
General_Accessories_E
86 Pages
-
19inch_Accessories_E
18 Pages
-
Elmaset_Frontpanels_Handles_E
80 Pages
-
Desktop_and_Compact_Cases_E
261 Pages
-
FLEXCOM
4 Pages
-
Defense
44 Pages
-
VITA Catalog
93 Pages
-
Elma Electronic PICMG Catalog
136 Pages
-
Optima Stantron Capabilities
16 Pages
-
Brochure Railway Solutions
16 Pages
-
System Platforms
2 Pages
-
Surelock Card Retainers
8 Pages
-
Rugged Cabinets
2 Pages
-
Brochure Embedded Computers
28 Pages
-
Brochure VPX and Open VPX
28 Pages
-
PRODUCTS FOR SCIENTIFIC RESEARCH
20 Pages
-
8016G-RS422-PMC-adapter
2 Pages
-
Datasheet Type 38 Cabinet
3 Pages
-
bo!sys-5030 - ITX
2 Pages
-
BO!SYS-6020 - EPIC
2 Pages
-
Datasheet bo!sys-5010 - ITX
2 Pages
-
bo!sys-1010 - COM Express
2 Pages
-
bo!sys-1020 - COM Express
2 Pages
-
bo!sys-5020 - ITX
2 Pages
-
Catalog Small Form Factor
28 Pages
-
CompactPCI Serial
16 Pages
-
VPX and OpenVPX by ELMA
28 Pages
-
ELMA 19"-MicroTCA blu!one
2 Pages
-
9289 XMCStor
2 Pages
Archived catalogs
-
MicroTCA
12 Pages
-
mtca4
12 Pages
-
Product & Services
12 Pages