30105F-D
7Pages

BOOfrilftjCfC™ 30105F-D TECHNICAL SPECIFICATIONS 30105F-D SIDE VIEW DIAGRAM WITH 44" FRAME HEIGHT • Maximum Vertical Reach 162 /49 m • Working Area 180 Degrees Standard (360 Optional) • Lifting Capacity • Boom Length • Crane Weight (Standard) • Winch Bare Drum Pull • Hydraulic Digger Radius • Powered Boom Sections • Overall Height • Operator Controls • Outrigger Type Front • Outrigger Spread Front • Outrigger Type Rear • Outrigger Spread Rear EQUIPMENT COMPANY Elliott Equipment Company Email: sales@elliottequip.com Rotating Standup

TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Crane Capacity: 60,000 lbs at 5’ load radius. system with integral LMI display in radio transmitter. Maximum Tip Height: 117’ height (162’ with optional 45’ jib) Load Moment Indicator System: System senses hoist cylinder pressures, boom length and boom angle with hydraulic function lockout. The display console is equipped with a bar graph showing crane utilization, boom angle or boom length, a mode select controls for main boom and jib operation, and an anti-two block with an audio/visual warning and shut-off functions to limit hook-boom...

TECHNICAL SPECIFICATIONS LOAD CHART - MAIN BOOM + DIGGER, FULL-SPAN OUTRIGGERS EQUIPMENT COMPANY WITH DIGGER MAIN BOOM LOAD RATINGS WITH FULLY EXTENDED OUTRIGGERS EQUIPMENT COMPANY Elliott Equipment Company Phone: 402-592-4500 Omaha, NE 68127 Email: sales@elliottequip.com

TECHNICAL SPECIFICATIONS LOAD CHART - MAIN BOOM + DIGGER, MID-SPAN OUTRIGGERS EQUIPMENT COMPANY WITH DIGGER MAIN BOOM LOAD RATINGS WITH OUTRIGGERS AT MID-SPAN POSITION BLOCK AGAINST BOOM TIP WHEN EXTENDING BOOM. - KEEP AT LEAST 5 WRAPS WIRE ROPE, AS SPECIFIED BELOW, WITH THE PROPER BREAKING STRENGTHS - ANTI-TWO-BLOCK SYSTEM OPERATING CONDITION BEFORE OPERATING CRANE. CRANE MEETS ASME B30.5 REQUIREMENTS AT TIME OF MANUFACTURE DO NOT PAINT OVER ANY LABELS EQUIPMENT COMPANY Elliott Equipment Company Email: sales@elliottequip.com

TECHNICAL SPECIFICATIONS RANGE CHART - MAIN BOOM + JIB, FULL-SPAN OUTRIGGERS EQUIPMENT COMPANY WITH DIGGER RANGE DIAGRAM WITH FULL SPAN OUTRIGGERS LOAD RADIUS FROM CENTERLINE OF ROTATION IN FEET 20'-0" FULL SPAN OUTRIGGERS OUTRIGGER LOCK PINS DISENGAGED AND BEAMS AT FULL HORIZONTAL EXTENSION 1. Operate jib by radius when main boom is full extended. Increase boom angle if necessary to maintain load radius. 2. When boom is retracted, operate jib by boom angles. Do not exceed any rated jib capacities at reduced boom lengths. 3. Capacities do not exceed 85% stability. 4. Load ratings above bold...

TECHNICAL SPECIFICATIONS RANGE CHART - MAIN BOOM + JIB, MID-SPAN OUTRIGGERS EQUIPMENT COMPANY WITH DIGGER RANGE DIAGRAM WITH OUTRIGGERS AT MID-SPAN POSITION LOAD RADIUS FROM CENTERLINE OF ROTATION IN FEET OUTRIGGER LOCK PINS ENGAGED 1. Operate jib by radius when main boom is full extended. Increase boom angle If necessary to maintain load radius. 2. When boom is retracted, operate jib by boom angles. Do not exceed any rated jib capacities at reduced boom lengths. 3. Capacities do not exceed stability based on ISO 4305-1991. 4. Load ratings above bold line are structurally limited. 5....

TECHNICAL SPECIFICATIONS TRUCK CHASSIS SPECIFICATIONS Frame Section Modulus Front Axle Gross Weight Rating Rear Axle Gross Weight Rating Integral Front Frame Rails Required for Front Stabilizer Chassis data is minimum general requirements-not for engineering. Actual dimensions and truck data will depend on truck selection and axle configuration. *Minimum chassis weight is required to meet 85% stbility requirements. OPTIONS Hydraulic Pole Claw Combine Elliott’s digger system with a hydraulic pole claw to dig holes and place poles with a single machine. Tool Boxes Optional tool boxes and bed...