*mydirectindustry

1056F

Product catalog summary

Technical Specifications Overview
The 1056F BoomTruck by Elliott Equipment Company is designed for heavy lifting and versatile operation. Key specifications include a maximum vertical reach of 96 feet (29.2 meters) and a lifting capacity of 20,000 lbs (9,072 kg). The boom length is 56 feet (17.1 meters), and the crane weight is 13,390 lbs (6,074 kg). The crane features a three-section fully proportional boom and dual operator standup controls.

Crane Features

Control Console: Equipped with dual operator standup control stations, featuring four single-axis control levers, a bubble level gauge, and various operational indicators.
Boom: Constructed from high-strength steel, the boom includes a floating upper sheave and two lower sheaves, with a maximum tip height of 66 feet (96 feet with optional jib).
Winch: Positioned at the boom base, the winch is driven by a hydraulic motor and includes a burst-of-speed feature for increased line speed.
Load Moment Indicator System: Monitors hoist cylinder pressures, boom length, and angle, with hydraulic function lockout and anti-two block features.

Outriggers and Frame

Outriggers: Includes "A" Frame main outriggers with a 17'7" span and underslung "A" auxiliary outriggers with a 10'4" span.
Frame: Features a full-length, all-welded rigid 4-plate design sub-frame, allowing for bolt-on additions.

Hydraulic and Safety Systems

Hydraulic System: Open center type with a cable-shift PTO and three-section gear pump.
Safety Equipment: Includes a 5:BC dry chemical fire extinguisher and operator manuals.

Options and Customizations

Telescopic Material Handling Jib
Radio Remote Controls
Superlink Short Jack Outriggers
Gravity Leveled Steel Basket

Chassis Requirements

Minimum chassis specifications include a 144" C.A., 13,000 lb front axle, and 33,000 lb GVWR.

Contact Information
Elliott Equipment Company, 4427 South 76th Circle, Omaha, NE 68127. Phone: 402-592-4500, Email: [email protected]

Catalog excerpts

TECHNICAL SPECIFICATIONS 1056F SIDE VIEW DIAGRAM • Maximum Vertical Reach 96 729.2 m • Working Area 180 Degrees Standard (360 Optional) • Winch Bare Drum Pull 12,800 lbs/5,806 kg • Powered Boom Sections • Overall Height • Operator Controls • Outrigger Type Front • Outrigger Spread Front • Outrigger Type Rear • Outrigger Spread Rear Dual Operator Standup EQUIPMENT COMPANY Elliott Equipment Company Email: [email protected]

Open the catalog to page 1

TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS Crane Capacity: 20,000 lbs at five feet load radius. one set of underslung “A” auxiliary outriggers with a 10’4” span. Maximum Tip Height: 66’ height (96’ with optional 30’ jib) Frame: Full length, all welded rigid 4-plate design sub-frame. Sub-frame allows for bolt-on addition of 16’ bed. Control Console: Dual operator standup control stations equipped with four single axis control levers for the main crane controls. Operator station includes bubble level gauge, engine start/ stop switch, signal horn button, variable speed foot throttle, lifting...

Open the catalog to page 2

TECHNICAL SPECIFICATIONS MAXIMUM LIFTING CAPABILITIES EQUIPMENT COMPANY RANGE DIAGRAM LOAD RADIUS FROM CENTERLINE OF ROTATION IN FEET ALLOWABLE LINE PULL - DO NOT DEADHEAD LINE BLOCK AGAINST BOOM TIP WHEN EXTENDING BOOM. - KEEP AT LEAST 5 WRAPS OF LOADLINE ON THE WINCH DRUM AT - USE ONLY 9/16' DIAMETER WIRE ROPE, AS SPECIFIED BELOW, WITH THE PROPER BREAKING STRENGTHS - ANTI-TWO-BLOCK SYSTEM MUST BE IN GOOD OPERATING CONDITION BEFORE OPERATING CRANE. SEE OPERATION & SAFETY MANUAL. -MAXIMUM CAPACITY WITH DEDUCTIONS FROM RATED LOADS FOR HANDLING DEVICES SUPPLIED BY ELLIOTT EQUIPMENT CO, OVERHAUL...

Open the catalog to page 3

TECHNICAL SPECIFICATIONS CHASSIS SPECIFICATIONS Frame Section Modulus Front Axle Gross Weight Rating Rear Axle Gross Weight Rating Integral Front Frame Rails Required for Front Stabilizer Chassis data is minimum general requirements-not for engineering. Actual dimensions and truck data will depend on truck selection and axle configuration. *Minimum chassis weight is required to meet 85% stbility requirements. OPTIONS Radio Remote Control Interference protected radio remotes let you get closer to your work and have full control over your machine. Tool Boxes Optional tool boxes and bed storage...

Open the catalog to page 4

1056F

1056F

Catalog excerpts

All Elliott Equipment Company catalogs and technical brochures