*mydirectindustry

E-KC-200-H SERIES

Product catalog summary

Description
E-KC-200-H is a head-mounted, two-wire temperature transducer that adheres to the HART protocol. It converts measured values into a 4-20mA current signal based on a configured scale. It supports thermocouple and resistance thermometer sensors, as well as DC mV and resistor inputs. Configuration can be done via a HART configurator or special PC software from Elimko. Installation and maintenance should be performed by trained personnel, following the user manual. Unauthorized modifications are not permitted.

Technical Specifications

Power Supply: 9.0 – 36 V DC
Voltage Drop: 9.0 V
Isolation Voltage: 1.0 kV AC
Operating Environment: -20°C to +60°C, <95% RH (Non-condensing)
Storage Temperature: -25°C to 65°C
Protection Class: IP00
Calibration Temperature: 25°C ± 3°C
Dimensions: Ø 44.0 mm x 22.0 mm
Connection Cables: Max. 1.5 mm² (AWG 16)
Output: 4-20 or 20-4 mA
Sensors Supported: Various thermocouples and resistance thermometers
Load Resistance: < (Vç-9) / 0.021) Ω
Fault Warning: 3.8 mA or 21.0 mA
Reading Rate: 2 readings/second
CJC Fault: < ±1.0ºC (Thermocouple Input)
EMC Immunity: < ± 0.5% Full Scale
Heating Period: Approximately 5 Minutes
Communication Interface: HART 7
Damping Setting: 0 - 60 seconds
Weight: 60 g

The controller complies with the European Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC.

Standard Working Limits
The document provides detailed working limits for various sensors, including RTD and thermocouple types, with specified lower and upper limits, minimum scale, and accuracy.

Application Sample and Dimensions
The document includes an application sample and dimensions, though specific details are not provided in the text.

Catalog excerpts

E-KC-200-H SERIES HEAD-MOUNTED TYPE TEMPERATURE CONVERTER WITH HART PROTOCOL E-KC-200-H is a head-mounted type two-wire temperature transducer conforming to the HART protocol. Converters converts the measured value to a 4-20mA current signal according to the configured scale. Thermocouple and resistance thermometer type temperature sensors can be connected to the input of the converter. Power Supply Voltage Drop Isolation Voltage Operating Environment Temperature DC mV and resistor can also be connected to the converter input. Storage Temperature E-KC-200-H converter can be configured with the HART configurator or a special PC software available from Elimko. Operating Environment Moisture Protection Class Calibration Temperature Connection Cables Thermocouple: B, E, J, K, N, R, S, T, L, U Resistance Thermometer: Pt-50, Pt- 100, Pt-500, Pt-1000, Ni-50, Ni100, Ni-120, Ni-200, Ni-500, Ni-1000 Milivolt: -200 and 1000 mV Resistance: 0 and 5000 ohm Load Resistance Fault Warning Reading Rate CJC Fault (Thermocouple Input) Heating Period Communication Interface Damping Setting Installation, repair and maintenance service of E-KC-200-H should be done by trained technical personnel. The technical staff who will do this should read and understand the manual of the converter carefully and intervene. If the information given in the user manual is not sufficient, your company should contact Elimko. Making modifications for the converter or rendering repair-maintenance services in case of malfunction can only be allowed as permitted in user manual. Company using the product, may perform installation in conformity with the national regulations and realize repair-maintenance. • This controller complies with the European Low Voltage Directive 2006/95/EC, by the application of safety standard TS EN 61010-1. (Pollution degree 2) • This controller complies with the EMC Directive 2004/108/ EC by the application of EMC stan

Open the catalog to page 1