STANDARD MACHINE ELEMENTS WORLDWIDE

Levelling elements - Hygienic Design HYGIENIC DESIGN Maximum hygiene is a fundamental requirement, not only where food is produced. Hygiene also plays an increasing role in other industrial areas, from the pharmaceutical industry to the manufacture of paints and dyes. Nowadays a major issue is the manufacture of products without added preservatives or with as few added preservatives as possible while still achieving a long shelf life. However, this can only be achieved in a production environment in which all risks of contamination with microorganisms or dirt are excluded. For plant construction,...

DESIGN REQUIREMENTS DESIGN PRINCIPLES - Non-rusting Stainless Steels - FDA and EU compliant plastics and elastomers SURFACES - Surfaces must be able to be cleaned - Steps due to appliance configurations which are not aligned must be avoided - Seals must be designed so that no gaps occur - O-ring grooves must be hygienically designed - Contact with the product to be manufactured must be ruled out - Corners should preferably have a radius of 6 mm or more EHEDG - European Hygienic Engineering & Design Group Non-profit European consortium of machine and food manufacturers as well their suppliers,...

Levelling elements - Hygienic Design Stainless steel MATERIAL Fine turned AISI 304 stainless steel. UPPER SEAL OF THE PROTECTIVE SLEEVE (GBS) NBR synthetic rubber hardness 70 +/-5 Shore A, blue colour in compliance with FDA. LOWER SEAL OF THE PROTECTIVE SLEEVE (GBI) Polyurethane elastomer TPU hardness 95 +/-5 Shore A, blue colour in compliance with FDA. STEM SEAL (GST) H-NBR synthetic rubber hardness 85 +/-5 Shore A, blue colour, in compliance with FDA. BASE SEAL (GBA) Silicone hardness 85 +/-5 Shore A, blue colour in compliance with FDA. FEATURES AND APPLICATIONS LMHD levelling elements are...

Levelling elements - Hygienic Design with holes for ground mounting, stainless steel MATERIAL Fine turned AISI 304 stainless steel. UPPER SEAL OF THE PROTECTIVE SLEEVE (GBS) NBR synthetic rubber hardness 70 +/-5 Shore A, blue colour in compliance with FDA. LOWER SEAL OF THE PROTECTIVE SLEEVE (GBI) Polyurethane elastomer TPU hardness 95 +/-5 Shore A, blue colour in compliance with FDA. STEM SEAL (GST) H-NBR synthetic rubber hardness 85 +/-5 Shore A, blue colour, in compliance with FDA. BASE SEAL (GBA) Silicone hardness 85 +/-5 Shore A, blue colour in compliance with FDA. FEATURES AND APPLICATIONS...

Screws and nuts - Hygienic Designfor levelling elements, stainless steel INOX MATERIAL AISI 316L stainless steel. PACKING SEAL H-NBR synthetic rubber hardness 85 +/-5 Shore A, blue colour, in compliance with FDA. STANDARD EXECUTIONS - NTHD-SST-MT: threaded blind hole, matte finish. - NTHD-SST-PL: threaded blind hole, mirror polished finish (RA < O,8p). - NTHD-SST-p-MT: threaded screw, matte finish. - NTHD-SST-p-PL: threaded screw, mirror polished finish (RA < O,8p). FEATURES AND APPLICATIONS NTHD-SST screws and nuts are accessories for mounting the levelling elements used in environments where...

Screws and nuts - Hygienic Design NTHD-SST-p-MT NTHD-SST-p-PL iNoxl-tsrl NTHD-SST-p-MT Models all rights reserved In accordance with the law. Always mention the source when reproducing our drawings and photos.

etefa ELESA S.p.A. Via Pompei, 29 20900 Monza (MB) Italy Phone +39 039 2811.1 Fax +39 039 836351 [email protected] MIX Paper from responsible sources FSC® C003498 elesa.com © Copyright ELESA 2017