Fluted grip, three-arm, wing knobs with torque limiting STANDARD MACHINE ELEMENTS WORLDWIDE

Fluted grip, three-arm, wing knobs with torque limiting Elesa torque limiting products allow for the regulation of the maximum tightening torque most suitable for your needs. They may be used in various sectors where a sufficiently high tightening torque is required in order to obtain fast and secure fastening, such as laboratory equipment, key duplicators, tool sharpening and sports equipment. A wide range of applicable torques Easy adjustment Elesa torque limiting clamping elements cover a wide range of applicable torques, from 0.2Nm to 6Nm. Different shapes available for one optimal grip Elesa...

Fluted grip knob for GN 3663 clamping on a wide range of torques. Models all rights reserved In accordance with the law. Always mention the source when reproducing our drawings and photos.

Adjustable torque limiting knobs Technopolymer ELESA Original design MATERIAL Glass-fibre reinforced polyamide based (PA) technopolymer black colour, matte finish. CLOSING CAP Polyamide-based (PA) technopolymer RAL 7035 grey colour, push-fit assembly. STANDARD EXECUTIONS - MZD-A: black-oxide steel boss, threaded blind hole. - MZD-p: black-oxide steel threaded screw, chamfered flat end UNI 947 : ISO 4753 (see Catalogue 166 Technical data on page A-11). FEATURES AND APPLICATIONS The knob MZD incorporates a mechanism (ELESA patent) which, screwing clockwise until locking, reaches the required torque...

Adjustable torque limiting knobs TORQUE ADJUSTMENT 1. Remove the cap by inserting a screwdriver in the special slot. 2. The factory setting of the knob is 0.5 Nm. To increase or decrease the torque value, axially change the position of the disc with graduations by moving the center screw by means of a hexagonal key (ch = 2.5). The nominal value of the torque can be read on the small inclined plane at the disc level in correspondence with the reference mark, and it is adjustable between 0.2 and 1 Nm. The accuracy of the nominal value of the torque depends on the accuracy with which the adjustment...

Torque limiting knob KNOB BODY Glass-fibre reinforced polyamide based (PA) technopolymer, black colour, matte finish. CENTRE CAP Polyamide-based (PA) technopolymer, RAL 7035 grey colour, matte finish. TORQUE LIMITING MECHANISM Hardened steel. STANDARD EXECUTIONS Zinc-plated steel boss with threaded blind hole. -- VTD-AZ-2: maximum torque 2Nm. -- VTD-AZ-3: maximum torque 3Nm. -- VTD-AZ-4: maximum torque 4Nm. -- VTD-AZ-6: maximum torque 6Nm. FEATURES AND APPLICATIONS VTD knob is used when the applied tightening torque must not exceed a certain value. The transmission of the torque from the knob...

Torque limiting knobs Code 35601-2N 35601-3N 35602-2N 35602-3N 35611-4N 35611-6N 35612-4N 35612-6N 35613-4N 35613-6N # Maximum torque Models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings and photos.

Torque limiting knob Aluminium and steel KNOB BODY Anodised aluminium black colour CENTRE CLOSING CAP Acetal resin based (POM) technopolymer, light-grey colour TORQUE LIMITING MECHANISM Black-oxide steel. STANDARD EXECUTIONS Black-oxide steel clamping element, screw, spring and thrust washer - GN 3663 (d2): threaded hole. - GN 3663 (d4 - l): threaded screw. FEATURES AND APPLICATIONS GN 3663 knobs are used when the applied tightening torque (see C# ±10% in the Table) must not exceed a certain value. The torque transmission from the knob to the clamping element takes place by means of a spring...

Torque limiting knob Models all rights reserved In accordance with the law. Always mention the source when reproducing our drawings and photos.

Torque limiting knob Models all rights reserved In accordance with the law. Always mention the source when reproducing our drawings and photos.

Torque limiting wing knobs Technopolymer MATERIAL Glass-fibre reinforced polyamide based (PA) technopolymer, black (C9) or orange (C2) colour matte finish. TORQUE LIMITING MECHANISM Nickel-plated steel. STANDARD EXECUTIONS - CTD-B-2: nickel-plated steel boss with threaded blind hole, maximum torque 2Nm. - CTD-B-3: nickel-plated steel boss with threaded blind hole, maximum torque 3Nm. - CTD-p-2: nickel-plated steel threaded screw, maximum torque 2Nm. - CTD-p-3: nickel-plated steel threaded screw, maximum torque 3Nm. FEATURES AND APPLICATIONS CTD wing knobs are used when the applied tightening...

etefa ELESA S.p.A. Via Pompei, 29 20900 Monza (MB) Italy phone +39 039 2811.1 fax +39 039 836351 [email protected]