Catalogs >
ELESA >
DD51-E

DD51-E
2Pages

Catalog excerpts

Electronic digital position indicator INOX STAINLESS STEEL direct drive, 5-digit display, technopolymer BASE AND CASE High-resistance polyamide based (PA) technopolymer. Black base. Case in the following colours: - C2: RAL 2004 orange, glossy finish. - C3: RAL 7035 grey, glossy finish. Available on request in RAL 7021 grey-black colour (C1). Cover with perfectly sealed gasket and AISI 304 stainless steel UNI 6955 type self-tapping screws with six-lobe socket TORX®T06 (registered trademark by TEXTRON INC.). The ultrasonic welding between the base and the case prevents separation and avoids dust and liquid penetration. BOSS AISI 304 stainless steel with Ø 14 mm H7 reamed hole, fitting to shaft by means of AISI 304 stainless steel grub screw, hexagon socket and cup end UNI 5929-85, included in the supply. WINDOW Transparent polyamide based (PA-T) technopolymer, moulded over the case and with a perfect seal. Resistant to solvents, oils, greases and other chemical agents (avoid contact with alcohol during cleaning operations). DISPLAY - 5-digit LCD of 8 mm height and special characters. The visualization parameters can be set and modified by the operator by means of appropriate keys: - values displayed in mm, inches or degrees - display of mode for use (absolute or incremental mode) - reading orientation (right or reverse). KEYBOARD Polyester membrane. Resistant to solvents, alcohol, acids, alkalis. ACCESSORIES ON REQUEST (TO BE ORDERED SEPARATELY) - MDX-51: polyamide based (PA) technopolymer knob. - RB51-SST: AISI 304 stainless steel reduction sleeves. INTERNAL GASKET O-ring front sealing in NBR synthetic rubber, between the case and the boss. Brass bushing with double O-ring sealing in NBR synthetic rubber inside the rear cavity of the base (DD51-E-SST-IP67). Position indicators - BSA51-E: die-cast zinc alloy bases for spindle locking, epoxy resin coating, black colour, matte finish. GN 302.1 adjustable handle with die-cast zinc alloy lever body and AISI 304 stainless steel clamping element. A Ø 6.1 mm hole to fit the referring pin of the indicator. Handle positioned either on the right or on the left. Fitting to the machine by means of two M4 cylindrical-head screws (not included in the supply). ASSEMBLY INSTRUCTIONS 1. Drill a Ø 6 mm by 10 mm hole in the body of the machine with a 22 mm centre distance from the spindle to fit the rear referring pin. 2. Fit the indicator onto the spindle and make sure that the referring pin fit the hole. 3. Clamp the boss to the spindle by tightening the grub screw with hexagon socket and cup end, according to UNI 5929-85. STANDARD EXECUTIONS - DD51-E-SST-IP65: completely sealed indicator with IP 65 protection class, see EN 60529 table (on page A-19). - DD51-E-SST-IP67: completely sealed indicator with IP 67 protection class, see EN 60529 table (on page A-19) obtained by means of a brass bushing with double seal ring inside the rear cavity of the base. REAR GASKET Foam polyethylene, supplied. Models all rights reserved in accordance with the law. Always mention the source when reproducing our drawings and ph

Open the catalog to page 1

Electronic digital position indicator FEATURES AND APPLICATIONS DD51-E position indicators, with battery power supply, can be used on passing through shafts in any position to provide the reading of the absolute or incremental positioning of a machine component. The 5-digit display of 8,0 mm height ensures excellent readability even from a distance and from different viewing angles. The window in transparent technopolymer protects the LCD display against accidental shocks. The high protection degree, IP 65 or IP67, makes the indicator suitable for applications that require frequent washing,...

Open the catalog to page 2