*mydirectindustry

Catalogs
ELC construction électronique
oem din rail power supplies

oem din rail power supplies

Product catalog summary

Specifications Overview
This document outlines the specifications for OEM modular and regulated power supplies, highlighting key features such as protection mechanisms, voltage and current specifications, and compliance with safety and EMC standards.

Protection Features

Includes overcurrent and short-circuit protection using fuses and electronic systems.
Voltage inversion protection is provided.
Complies with safety standards EN 61010-1, EN 61010-2-201, and EMC standards EN 61000-6-2, EN 61000-6-4.
Rated for Overvoltage Category II and Pollution Degree 2.
Designed for operation below 2000 meters altitude with protection level IP30.

Voltage and Current Specifications

Output voltages are adjustable from 10 to 15 V, with configurations for 12 V and 24 V systems.
Regulation and ripple specifications ensure minimal voltage fluctuations.
Maximum current outputs vary by model, with some models supporting up to 25 A.
Power outputs range from 30 W to 300 W depending on the model.

Installation and Mounting

Modular polycarbonate cases with integrated clips for DIN rail mounting.
Options available for panel mounting with removable wall mounting clips.

Additional Features

Remote sensing to correct voltage drops in power lines.
LED indicators for power-on and fault status.
Some models include built-in active power factor correction (PFC).

Environmental and Safety Compliance

Operating temperature ranges from -25°C to +70°C with derating considerations.
Dielectric strength up to 4000 VAC between input and output.
Complies with Safety Extra Low Voltage (SELV) standards.

Conclusion
These power supplies are versatile and reliable, offering precise voltage regulation, robust protection features, and compliance with international safety standards, suitable for a wide range of electronic system applications.

Detailed Specifications

Input Voltage: Ranges from 190 to 440 Volts, 50/60 Hz, with variations for different models.
Output Voltage: Adjustable from 5 to 30 V depending on the model, with specific settings for battery charging.
Current: Maximum current varies by model, with short circuit conditions specified.
Power Consumption: Maximum power consumption ranges from 34.5 W to 360 W.
Protection: Includes short circuit, overcurrent, overtemperature, and reverse polarity protections.
Safety and Compliance: Complies with EN 61010-1, EN 61010-2-201, EN 61000-6-2, and EN 61000-6-4 standards.
Mounting: Designed for DIN rail or wall mounting with various terminal block configurations.

Key Features

Remote Sensing: Available in some models to correct voltage drop in wires.
Power Factor Correction (PFC): Built-in active PFC in certain models.
Indicators: LED indicators for power status, battery charging, and fault conditions.
Ripple and Regulation: Low ripple and precise voltage regulation across models.
Environmental Conditions: Operating temperatures range from -25°C to +70°C, with derating specified for higher temperatures.

Applications

Suitable for OEM applications, automation systems, and environments requiring regulated power supplies.
Designed for use with programmable logic controllers (PLCs) and other automation peripherals.

Technical Specifications

Input Voltage: 230/400 V ±15 V AC, single or two-phase, 50/60 Hz.
Mains Input: Spring terminal block with levers.
Max Wire Cross Sectional Area: 1.5 mm² (AWG 16) for mains input, 2.5 mm² (AWG 12) for earth terminal.
Safety: Class I, complies with EN 61558-2-6.
Protection Level: IP 30.
Output Voltage: Complies with EN 61131-2 for automation systems, 24 VDC.
EMC: Complies with EN 61000-6-2 and EN 61000-6-4.
Power Consumption: 287 W max.
Operating Temperature: 5 to 55 °C.
Dielectric Strength: 4500 VAC from input to output, 2250 VAC from input to chassis, 500 VAC from output to chassis.
Presentation: Galvanized steel case and front panel with epoxy finish.

Mounting

Integral symmetrical DIN rail clips for easy installation.

Voltage

Floating outputs on 2 spring terminal blocks with levers.
Output voltage: 24 VDC with a ripple of less than 5%.
Hold up time: 20 ms at nominal voltage and current.
Indicator: Green power-on LED indicator.

Current

Maximum current: 10 A.
Current/Voltage/Ripple:
- 0 A: 28.1 V, 0% ripple.
- 2 A: 26.7 V, 1% ripple.
- 4 A: 25.9 V, 2% ripple.
- 6 A: 25.3 V, 3% ripple.
- 8 A: 24.6 V, 4% ripple.
- 10 A: 24.0 V, 5% ripple.

Power

Output power: 240 W.

Protection

Short circuit protection by fuse in the secondary circuit.

Features

Universal input: 230/400 V ±15 V.
Compliant with EN 61131-2 for PLCs and other applications requiring 24 V filtered rectified power.
Easy installation with direct DIN rail mounting and spring terminal block.
High output with toroidal safety transformer (SELV).
Compact and lightweight design.

Catalog excerpts

OEM BACKUP SYSTEMEAN CODE : 3760244880338 UNIVERSAL 12 V or 24 V MS122402 UNIVERSAL : direct operation for 12 or 24 V system CONTROL : state of faults on relay status PRACTICAL : batterie charge current adjustable from 0,3 to 2 A Toggle push of release the " by-pass " system FASTER : screw terminal blocks PROTECTED : against short-circuits in the mains & battery polarity inversion EASY: direct DIN rail or panel mounting INTELLIGENT : Preponderance to start, on AC input or battery 10 A MAX 12V or 24V for Lead-acid battery from 2 to 20 Ah 12 or 24 V auto configuration. • For operation with lead-acid batteries •_Connexion_on_disconnect_screw_terminal_block_for_2,5mm2_wires_(AWG12). Protection • Against overcurrent or short-circuits in the primary by 10A fuse • Against voltage inversion by electronic protection and by fuse Other specifications II ; Pollution Degree : 2. <2000 m. IP30 : +5°C to +50°C 150 mA 2500 VAC from input to output Presentation modular polycarbonate case (3 modules) screenprinted Dimension : 54 x 95 x 58 mm (lxhxp) Mounting : Case integrated clips for symetrical DIN rails 35x7,5 mm or 35x15 mm. Case removable wall mounting clips for 4 mm screws. Sector supervision • Inputs on disconnect screw terminal block for 2,5 mm2 wires (AWG12). • Input voltage : 230 V ±10%. Power consumption : 0,2 W • Detection : by coupler and automatic switch without power cut. Battery supervision • Supervision system of status and current charge of the battery • Discharge limiter system (DLS) : disjonction at 90% voltage rms • Monitoring : " by-pass " push toggle to start only on battery.

Open the catalog to page 1

MODULAR SYMMETRICAL & REGULATED POWER SUPPLY + 15 V or 12 V or 24 V ALE1502D PRECISE : Switching power supply offering a ripple < 3 mV rms - Output voltage adjustable from ±10 to ±15 V SMALL : Modular, EASY: direct DIN rail or panel mounting PROTECTED : against short circuits and reverse polarity. mil- RESISTANT TO SHOCK 60 WATTS ±10 to 15 V 2 A or 12V 5 A or 24V 2 A • Floating outputs on spring terminal block with levers for 2,5 mm2 (AWG 12) wires. • Balanced-output voltage adjustable from ±10 to ±15 V +15V output • Regulation : < 20 mV for a load variation from 0 to 100%. < 2 mV for a line...

Open the catalog to page 2

OEM MODULAR & REGULATED POWER SUPPLY EAN CODE : 3760244880246 Panel mounting PRECISE : Output ripple < 3 mV rms. - Remote sensing to overcome voltage drop in the power lines. PRACTICAL : Output voltage adjustable from 10 to 15 V. - Spring terminal block. PROTECTED : Short circuit protection. EASY : Direct DIN rail or panel mounting. • Floating outputs on spring terminal block for 2,5 mm2 (AWG12) wires • Output voltage : adujustable from 10 to 15 V. • Regulation : <25 mV for a load variation from 0 to 100% 5 mV for a line variation from -10 to +10% • Ripple : < 3 mV rms including : 3 mV peak to...

Open the catalog to page 3

OEM MODULAR & REGULATED POWER SUPPLYEAN CODE : 3760244880253 12 V REMOTE-SENSING ALE1205 1, 135 , PRECISE : Switching power supply offering a ripple < 3 mV rms. - Output voltage adjustable from 10 to 15 V SMALL : Modular, EASY : Direct DIN rail or panel mounting. PROTECTED : against short circuits and reverse polarity. RESISTANT TO SHOCK Specifications Voltage • Floating outputs on spring terminal block with levers for 2,5 mm2 (AWG 12) wires. • Output voltage : adjustable from 10 to 15 V. • Regul : < 20 mV for a load variation from 0 to 100% < 2 mV for a line variation from -10 to+10%. • Ripple...

Open the catalog to page 4

OEM REGULATED POWER SUPPLY EAN CODE : 3760244880260 PRECISE : Output ripple < 3 mV rms. COMPLIE : EN 61000-3-2 Built in actif power corrector (PFC). PRACTICAL : Output voltage adjustable from 10 to 15 V. PROTECTED : Short circuit protection. EASY : Direct DIN rail mounting. - Dual spring terminal block. Specifications Voltage • Floating outputs on dual spring terminal block for 2.5mm² (AWG 12) wire • Output voltage : adjustable from 10 to 15 V. • Regulation : < 25 mV for a load variation from 0 to 100%. < 1 mV for a line variation from -10 to +10%. • Ripple : < 3 mV rms including: < 5 mV peak...

Open the catalog to page 5

constmctlon electronlque EAN CODE : 3760244880277 12 V PRIM 190 TO 440 V + ACTIVE PFC # PRECISE : Output ripple < 3 mV rms. COMPLIE : EN 61000-3-2 Built in actif power corrector (PFC). DIAGNOSTIS : Ala rm by Relay with invert contact. PRACTICAL : Output voltage adjustable from 10 to 15 V. UNIVERSAL : 190 to 440 V main input voltage. POWERFUL : To cumulate n+1 (Parallel active mode). PROTECTED:aga inst short circuit. EASY : Direct DIN rail mounting - Spring terminal block. DC POWER SUPPLY LOAD SHARE CONTROLLED DC OUTPUT 12V 25A (TO - 15V; 25 - 20A> PARALLEL MODE Voltage • Floating outputs on dual...

Open the catalog to page 6

OEM REGULATED POWER SUPPLY AL 912AES , EASY : DIN rail or wail mounting. " QUICK : Screw terminal blocks. PRACTICAL : Power-on indicator. PROTECTED : Triple protection. - Optional protective cover. • EMC • Installation altitude • Input voltage • Mains input • Power consumption • Dielectric strength • Insulation resistance • Presentation • Optional Voltage • Floating outputs on screw terminal block for 2,5 mm2 rigid or 1,5 mm2 flexible wire. • Output voltage : 24 Volts (set). • Accuracy : ± 0,5%. • Regulation : < 40 mV for a load variation from 0 to 100%. < 10 mV for a 10% line variation. • Ripple...

Open the catalog to page 7

OEM MODULAR & REGULATED POWER SUPPLY ]PRECISE : Output rippte < 3 mV rms. - Remote sensing to overcome vottage drop in the power lines. PRACTICAL : Output voltage adjustable from 20 to 30 V. - Spring terminal block. PROTECTED : Short circuit protection. EASY : Direct DIN rail or panel mounting. Regutation Rippte Hotd-up time Indicator Voltage • Floating outputs on spring terminal block for 2,5 mm2 (AWG12) wires Output vottage : adujustabte from. 20 to 30 V. < 20 mV for a toad variation from. 0 to 100% 5 mV for a tine variation from -10 to +10%. < 3 mV rms inctuding : 3 mV peak to peak of the...

Open the catalog to page 8

oem din rail power supplies

oem din rail power supplies

Catalog excerpts

All ELC construction électronique catalogs and technical brochures