ELAFLEX Catalogue Section 2: Hose Fittings
55Pages

{{requestButtons}}

Catalog excerpts

ELAFLEX Catalogue Section 2: Hose Fittings - 1

Armaturen Hose Fittings Raccords Raccordi per tubi

Open the catalog to page 1
ELAFLEX Catalogue Section 2: Hose Fittings - 2

Weight Approx. Thread Type + Size Part  Number links left links left Same as Type M, but union nut and ferrule chrome plated. Captive seal polyurethane Schlauchstutzen aus 1.4571. Mutter aus 1.4571 (1.4408). Hülse aus Messing verchromt. Dichtung PTFE Stutzen + Hülse aus Alu, nicht verchromt / 3) Hose tail + ferrule of aluminium, not chrome plated Mutter + Hülse verchromt / Union nut + ferrule chrome plated 4) Werksmontierte Hülsen-Mutterverschraubungen, nicht demontierbar. Anschlussmaße entsprechend EN 14424. Nenndruck 25 bar. Lieferung nur als komplette Schlauchleitung, da Spezialmaschine...

Open the catalog to page 2
ELAFLEX Catalogue Section 2: Hose Fittings - 3

Sonderausführungen + Zubehör ·  Special Types + Accessories 1 für for WERKSTOFF Material BESTELLNUMMER Part Number Polyurethan /polyurethane Polyurethan /polyurethane Polyurethan /polyurethane Polyurethan /polyurethane Polyurethan /polyurethane Polyurethan /polyurethane Polyurethan /polyurethane Spare Seals for hose fittings with union nut Spezialdichtung NYD aus Polyamid, für Vaterverschraubungen mit Gewindehinterdrehung. Wird verwendet, wenn bei flachdichtenden Gewindeverbindungen auf der Mutterseite keine sichere Abdichtung erreicht werden kann. Sonderausführung für Schlauch LPG 10 für...

Open the catalog to page 3
ELAFLEX Catalogue Section 2: Hose Fittings - 4

Weight Approx. Thread Type + Size Part  Number Type V-SS Hose tail with male thread of stainless steel AISI 316 Ti. Ferrule of brass, chrome plated G = Gewinde nach EN ISO 228 / to EN ISO 228 / BSP parallel R = Gewinde nach EN 10226-1 / to EN 10226-1 / BSPT taper Werksmontierte Hülsen-Vaterverschraubungen, nicht demontierbar. Schlauchstutzen und Hülse Messing (Cr : verchromt) Type V-NR Hose tail and ferrule of brass, (Cr : chrome plated) Schlauchstutzen aus Edelstahl 1.4571. Hülse aus Messing blank verchromt Hose tail and ferrule of brass, chrome plated Schlauchstutzen und Hülse: Messing...

Open the catalog to page 4
ELAFLEX Catalogue Section 2: Hose Fittings - 5

Montage von Schraubhülsen-Einbindungen  ·  Assembly Instructions Ferrule Type 1 Als Voraussetzung für eine betriebssichere Montage muss der äußere Durchmesser des Schlauches dem umseitigen 'OD'-Maß entsprechen. Maximale Toleranz ± 0,5 mm Before assembly please check whether the outer diameter of the hose conforms with the 'OD' measure listed overleaf. Maximum tolerance for safe assembly ± 0,5 mm Nach Montage des Stutzens prüfen, ob das Schlauchende noch im Kontrollfenster zu sehen ist. After assembly of the hose tail please check whether you can see the end of hose through the control...

Open the catalog to page 5
ELAFLEX Catalogue Section 2: Hose Fittings - 6

AUSFÜHRUNG · MATERIALIEN ANWENDUNGSBEREICH Application · Materials Part Number KS 16 TECHNISCHE ÄNDERUNGEN VORBEHALTEN · NACHDRUCK UND KOPIEN NUR MIT UNSEREM EINVERSTÄNDNIS · Specifications subject to change without notice · Copyright ELAFLEX KNICKSCHUTZ KS aus kälteflexiblem Polyurethan. Wirkungsvoller Schutz zur Verstärkung des stark beanspruchten Bereiches direkt hinter der Armatur. KS muss v o r Montage der Schlaucharmaturen angebracht werden. Special colours on request ANTI - KINKING SLEEVE KS of low temperature flexible polyurethane. Effective protection of the hose section near to...

Open the catalog to page 6
ELAFLEX Catalogue Section 2: Hose Fittings - 7

Imprint on Colour Sleeves ELAFLEX Sortentüllen Type CS dienen zur Herausstellung von Kraftstoffsorte oder Firmenfarbe. ELAFLEX Colour Sleeves type CS provide a clear emphasis on product grade or company colour. Für Verkaufswerbung oder wichtige Hinweise können die Sortenüllen zusätzlich mit einem kraftstoffbeständigen t Aufdruck versehen werden, siehe untenstehende Beispiele. It is possible to print advertisement or messages on the colour sleeves, see examples below. The imprint is fuel resistant. Ein nachträgliches Überziehen der Sortentülle über den Knickschutz KS ist möglich. The Colour...

Open the catalog to page 7
ELAFLEX Catalogue Section 2: Hose Fittings - 8

Andere Dichtungswerkstoffe, z. B. für heißes Wasser oder Lösungsmittel, siehe Seite 228 Other materials for seals, e.g. for hot water and solvents, see page 228 Schlauchstutzen aus 1.4571 (1.4408). Mutter aus 1.4408, 1.4571 oder 1.4301. Dichtung PTFE Hose tail of AISI 316 Ti (AISI 316). Union nut of AISI 316, AISI 316 Ti or AISI 304. Seal of PTFE Hose tail aluminium, union nut of brass L-Type ( PN 10 ): Stutzen Alu, Mutter Ms Hose tail and union nut aluminium. Captive seal of PU Alu-Type ( PN 10 ): Stutzen u. Mutter Aluminium. Dichtung Polyurethan Hose tail and union nut of hot stamped...

Open the catalog to page 8
ELAFLEX Catalogue Section 2: Hose Fittings - 9

Assembling SPANNFIX Safety Clamps Die Montage der SPANNFIX-Sicherheitseinbindung läßt sich leicht und schnell mit Standardwerkzeug gemäß Abbildungen ausführen. Umseitig ist in der Spalte 'OD' angegeben, in welchem Maßbereich der Außendurchmesser des Schlauches bei eingeschobenem Stutzen liegen muss. SPANNFIX passt für alle ELAFLEX-Schläuche, die innerhalb der angegebenen Werte liegen. Auch Schläuche anderer Hersteller lassen sich mit SPANNFIX montieren, wenn Abmessungen und Ausführung den ELAFLEX-Schläuchen entsprechen. Der große Spannbereich ergibt sich daraus, dass SPANNFIX auf der...

Open the catalog to page 9
ELAFLEX Catalogue Section 2: Hose Fittings - 10

Thread Type + Size Part  Number Vaterteil-Schlauchverschraubungen nach EN 14420-5 mit wiederverwendbarem SPANNFIX-Sicherheitseinband aus gepresstem Aluminium. Arretierstifte und Scharnierstifte aus Edelstahl. Nenndruck bis 25 bar. Chemische Beständigkeit siehe Seite 250. Hose couplings with male thread according to EN 14420-5 with re-usable SPANNFIX pinned safety clamps of hot stamped alu inium. Pins of stainless steel. Working pressure up to 25 bar. m Chemical resistance chart see page 250. Hose tail with male thread of brass Schlauchstutzen mit Außengewinde aus Messing Hose tail with male...

Open the catalog to page 10
ELAFLEX Catalogue Section 2: Hose Fittings - 11

Außengewinde-Schlauchstutzen mit Sägezahnprofil für SK-Schelleneinband. Lieferbare Typen: V 50 – 2" SK, V 75 – 3" SK. Nur für ungefährlichen Einsatz geeignet wie z. B. für Zement und Futtermittelschläuche ohne Spirale. Nicht zulässig für Flugzeugbetankungs-, Marine-, Dampf-, Heiß bitumenschläuche, LPG-Schläuche sowie Durchleitung von gefährlichen Chemikalien. Max. Nenndruck 10 bar. Hose tail with male thread and serrated profile for the attachment by SK clamps. Types: V 50 – 2" SK and V 75 – 3" SK. Only suitable for non dangerous application e. g. cement or feeding stuff hoses without steel...

Open the catalog to page 11

All Elaflex Hiby GmbH & Co. KG catalogs and technical brochures

  1. ZVG 2

    4 Pages

  2. Type SD

    2 Pages