Directional Control Valves Solenoid Operated Size D 06 (03) ·350 bar (5076 PSI) · 80 L/min(21 GPM) Size D 06 (03) • pmax 320 bar (4641PSI) according to CSA 4/3-, 4/2- way directional control valves Solenoids can be turned around their axis to any position Four-land spool - reduced functional dependence on fluid viscosity Push button manual override Installation dimensions to DIN 24 340 / ISO 4401 / CETOP RP121-H Subplates see data sheet HU 0002 Functional Description WE3 The RPE3 directional control valves consist of housing (1), a control spool (5) with two centering springs (4) and cylindrical operating solenoids (2, 3). The three-position directional control valves are fitted with two solenoids and two springs. Two-position directional control valves have either one solenoid and one return spring or two solenoids and a detent assembly. The operating solenoids are DC solenoids. For AC supply the solenoids are provided with a rectifiers which are integrated in the DIN connector socket as part of the solenoid. The connectors (6, 7) can be turned by 90°. By loosening the nut (8), the solenoids can be turned or replaced without interfering with any seals of the valve. In the case of solenoid malfunction or power failure, the spool of the valve can be shifted by manual override (9), provided the pressure in T-port does not exceed 25 bar. The valve housing (1) is phosphate coated and the solenoids (2, 3) are zinc coated.

Order Code Directional Control Valves Solenoid Operated Sensing of the end position no designation without sensor S1 normally-open sensor to 50 bar (725PSI) S2 normally-open sensor to 210bar (3045 PSI) S4 normally-closed sensor to 50bar (725 PSI) Valve size Number of valve positions two positions three positions Spool symbols see the table spool symbols Rated supply voltage of solenoids (at the coil terminals) 12 V DC / 2.72 A 24 V DC / 1.29 A 205 V DC / 0.15 A 230 V AC / 0.17 A / 50 (60) Hz The AC coils correspond with E5 type Soft Shift Spool speed control orifice no designation without damping...

Technical Data Valve size_ Maximum flow_ Max. operating pressure at porte P, A, B Max. operating pressure at port T Pressure drop Hydraulic fluid Hydraulic oils of power classes (HL, HLP) to DIN 51524 Fluid temperature range for NBR seals Fluid temperature range for FPM seals Viscosity range_ Maximum degree of fluid contamination Max. allowable voltage variation Duty cycle Service life Weigt - valve with 1 solenoid - valve with 2 solenoids Mounting position Spool Symbols

Operating limits for maximum hydraulic power transferred by the directional valve. For respective spool type - see spool symbols.

Valve Dimensions Dimensions in milimeters (inches) Valve with two solenoids Valve with one solenoid "a" Valve with one solenoid "b" 9.25 x 1.68 supplied with valve 8 Space required to remove connector Required surface finish of

Type of the Solenoid Coil Designation Dimensional sketch Solenoid coil with terminal for the electrical connector, EN 1745301-803. Solenoid coil with integrated quenching diode (bipolar transil diode) and terminal for the electrical connector, EN 1745301-803. Solenoid coil with terminal for AMP-Junior-Timer electrical connector. Solenoid coil with integrated quenching diode (bipolar transil diode) and terminal for AMP-Junior-Timer electrical connector. Solenoid coil with integrated rectifier and terminal for the electrical connector, EN 1745301-803. Manual Override STANDARD Standard model of...

Spool Speed Control Orifice Type Description Important: This directional valve provides control spool soft shifting by means of orifice situated in the solenoid armature.To ensure the proper function of the valve, perfect air bleeding of the solenoid is required (by us of bleeding plug (1). The plugs are accessible after removing the rubber boot (2) from the solenoid retaining nut (3). Switching times Switching time, on and off The switching times shown are valid for viscosity n = 32 mm /s (156 SUS) and nominal voltage. They are dependent upon working pressure and flow rate of the directional...

Spool Ship Position Sensor S1, S2 - Circuit diagram of the normally-open sensor - Circuit diagram of the normally-closed sensor Connector The proximity sensor transforms the spool position into an electrical step signal. It can be used with directional control valves with one or two solenoids. Technical Data of the Sensor S1, S4 S2 Rated power supply voltage V 24 DC Power supply voltage range V 10 ... 30 DC Rated current mA 200 Enclosure type of sensor to EN 60529 IP 67 Max. operating pressure bar (PSI) 50 (725) 210 (3046) Switching frequency Hz 1000 Ambient temperature range °C (°F) -25 ......

Electrical connector Solenoid coil Nut with seal Orifice in P port with seal ring Sensor Connector of position sensor with LED Seal kit Mounting bolts 4 Solenoid coil Solenoid type Coil type E3A Order number 24159600 24159800 Solenoid retaining nut with seal Type of the nut Seal ring Standard nut Closed nut 22 x 2 Nut with rubber boot Nut with detent assembly Connector of position sensor Type designation Model Max. input voltage K02 connector of position sensor with LED 10...30 V DC S1 normally-open sensor 10...30 V DC S2 normally-open sensor 10...30 V DC S4 normally-closed sensor 10...30 V DC...

HA 4010 Electrical connector, EN 1745301-803 Connector A grey Type K1 16202200 K5 16202600 K2 16202800 K3 16202400 K4 16203000 Electrical Connector, EN 1745301-803 Type Description connector - B (black) K1 connector - A (gray) connector - B (black) K5 connector - A (gray) Connector B black Ordering number 16202100 16202500 16202700 16202300 16202900 Max. input voltage Solenoid connections connector - A (gray) connector with LED and guenching diode - B (black) connector with LED and guenching diode - A (gray) M16x1.5 bushing bore Æ4-6 mm (0.16-0.24 in) 1/2 NPTF bushing bore Æ 6-8 mm (0.24-0.31...