CCR_A
2Pages

{{requestButtons}}

Catalog excerpts

CCR_A - 1

Compliance Device for assembly insertion with flange - A SERIES Center Master® compensates for errors (position and/or angular and/or torsional) occurred during an assembly that various precision parts are press or loose fitted into the holes. Thereby, it reduces assembly failure, enhances product quality, and shortens the cycle time in production line. Advantages • Significant reduction of assembly failure due to center position errors • Uniform press-fitting quality • Wide range of applications • Increased binding force between parts • Saves assembly line construction time, reduces equipment investment cost • Enhanced operation rate • Longer life cycle of the assembler • Simple maintenance SPECIFICATIONS Compensation range Allowable maximum force KN (Kgf) Compliance center length P mm (in) Elasticity coefficient (3) Axial direction Compressional N/mm (kgf/mm) Horizontal direction N/mm (kgf/mm) Torsional direction Nm/rad (kgf.cm/rad) (1) Model: customized order is available (2) This value can be doubled when Center Master is installed in the vertical direction upside down (reverse vertical). (3) Elasticity coefficient indicates the elasticity at the compliance center (P) - the average value calculated until the plate runs into the stopper. * Center Master® compensates up to +/-2 mm of positional error, but this value can vary depending on the chamfer size. Ambient temperature: 0-55 °C (32-131 °F) AUTOMATIC CORRECTION OF A POSITION/ANGLE ERROR Process of Center Error Correction Fixed section Floating section Insertion or press-fitting begins when both axes are aligned If the shaft contacts the hole's chamfer, the floating section moves sideways in parallel to the center position A shaft starts from a misaligned position in a Press-fit application Automatic Compensation of Angular Error Compliance center lenght (P) Automatic Compensation of Positional Error Compliance center Torsional direction Component (Axis side) Component (Hole side) Angle direction Horizontal direction Nonforced insertion: D>d It starts insertion with an angular misalignment The shaft moves along the chamfered surface when it comes in contact with one side of the hole When the shaft touches the other side of the hole, then insertion starts without angular error. (Angle error correction only applicable for insertion) EFFECTO GROUP • Compliance center lenght (P) The allowable tolerance of the P value is within ±5mm. If the P value exceeds the tolerable limit, the compensation function to correct misalignment may not work properly. • Payload Payload means the total weight of an assembly tool and a

Open the catalog to page 1
CCR_A - 2

PRODUCT INFORMATION with flange - A SERIES Size ABCDEF G HIJ K LMNO * Dimensions are in millimiters. ** All dimensions are descriptive and subject to variation for technical upgrading. We reserve the right to make variations without prior notification Applied Robotics 648 Saratoga Road Glenville, NY 12302 USA Tel. +1 518 384 1000 Fax +1.5183841200 info@appliedrobotics.com www.appliedrobotics.com EFFECTO GROUP S.p.A. Via Roma, 141/143 28017 San Maurizio d'Opaglio (NO) - Italy Tel. +39 0322 96142 Fax +39 0322 967453 info@effectogroup.com www.effectogroup.com

Open the catalog to page 2

All Effecto Group S.p.A. catalogs and technical brochures

  1. OPT

    2 Pages

  2. SWINGCUT 100

    2 Pages

  3. FLEXICUT 100

    2 Pages

  4. FLEXICHAM

    2 Pages

  5. BLQ-E

    2 Pages

  6. FLEXICHAM

    2 Pages

  7. QPGB

    2 Pages

  8. AR

    20 Pages

  9. AR-DIS

    10 Pages

  10. SR

    12 Pages

  11. PS

    16 Pages

  12. MD_MDE

    52 Pages

  13. QS7500

    2 Pages

  14. QS4500

    2 Pages

  15. UVP

    2 Pages

  16. UVH

    2 Pages

  17. BLQ_I

    2 Pages

  18. CCR_TS

    2 Pages

  19. CCR_T

    2 Pages

  20. CCR_SS

    2 Pages

  21. CCR_S

    2 Pages

  22. CCR_BS

    2 Pages

  23. CCR_B

    2 Pages

  24. CCR_LA

    2 Pages

  25. QS1500

    2 Pages

  26. QS800

    2 Pages

  27. QS400

    2 Pages

  28. FRC

    2 Pages

  29. QS200

    2 Pages

  30. QS50

    2 Pages

  31. MXC20

    2 Pages

  32. DTS 3 JAW

    2 Pages

  33. QS25

    2 Pages

  34. MXC 5

    2 Pages

  35. PRD

    2 Pages

  36. BLQ_E

    2 Pages

  37. ARPG15

    2 Pages

  38. QS-AW

    2 Pages

  39. QS3000

    2 Pages

  40. QS7

    2 Pages

  41. MADT

    10 Pages

  42. MAE

    16 Pages

  43. MAGNUM

    20 Pages

  44. GPAL - X-RAYS

    28 Pages

  45. OPL 3 JAW

    1 Pages

  46. OPL 2 JAW

    2 Pages

  47. LGE

    2 Pages

  48. OPE 2 JAW

    4 Pages

  49. OPE 3 JAW

    4 Pages

  50. QPG 2 JAW

    2 Pages

  51. QPG 3 JAW

    2 Pages

  52. OG 2 JAW

    2 Pages

  53. OPH 3 JAW

    2 Pages

  54. OPH 2 JAW

    2 Pages

  55. OG-A

    2 Pages

  56. OLE

    2 Pages

  57. OF

    2 Pages

  58. VRG

    2 Pages

  59. LPG

    2 Pages

  60. FRC

    1 Pages

  61. OPT

    2 Pages

  62. OPRING

    2 Pages

  63. QPG-tech

    2 Pages

  64. DTS 2 JAW

    2 Pages

  65. OSV-CM

    7 Pages

  66. AR COL

    10 Pages

  67. MAV

    17 Pages

  68. OSV

    21 Pages