MAGNESCALE
11Pages

MAGNESCALE digital gauge Content: Technical Data DT12, DT512 Technical Data DT32 Interpolator MT14, MT30 Accessories Displays Order code - Measurement ranges: 12, 32 mm (DT Series) - Resolution up to 1 µm - Linearity up to 2 µm - Output signal A/B, TTL-Linedriver, EIA-422 with MT14 - USB (2.0 FS) interface with MT30 - free evaluation software for download - Protection class up to IP64 - Spring loaded and pneumatic versions - Resistant against water and oil - Life cycle up to 30 million strokes

DIGITAL GAUGES DT12, DT512 Model Measurement range Resolution depending on the unit to be connected: 1 channel displays (e.g. LT10A-105): 100 / 2 channel displays (e.g. LT11A-201): 80 Spring push-out Reference point Working temperature Storage temperature Measuring force Protection class * Life cycle Steel ball tip ø3 mm, screw M2,5 Cable length compatible display *Excluding the interpolation box and connector DT12N, DT512N

DIGITAL GAUGE DT32 Model Measurement range Linearity (20°C) Displacement speed max. depending on the unit to be connected: 1 channel displays (e.g. LT10A-105): 100 / 2 channel displays (e.g. LT10A-205): 80 spring push-out Pneumatic push Reference point spring push-out Pneumatic push Working temperature Storage temperature Measuring force Protection class * Weight *Excluding the interpolation box and connector Steel ball tip ø3 mm, screw M2,5 compatible display Feeler Cable length

INSTALLATION INSTRUCTION Mounting method using mounting hole Mounting method using holder Mounting holder dimensions and tolerance

INTERPOLATOR MT14 Using the interpolator unit MT14 the digital gauges of the series DT12, DT32 and DT512 can directly be connected to PLCs etc. MT14 Resolution Output signal Voltage-differential line driver output (compliant with EIA-422) Working temperature Storage temperature 1.2 (when output load of 120 Ω is connected) Cable color 0 V and the shield (FG) are connected with a capacitor. Phase difference for phase A/B output in depending on the displacement speed v [m/min] MT14-01 * An alarm is output at a traveling velocity of 100 to 115 m/min. The sampling frequency of the

INTERPOLATOR MT30 Using the interpolator unit MT30 the digital gauges DT12, DT32 and DT512 can be connected to the USB port of a PC. Model Resolution Connectable digital gauge Accuracy (20°C) Protection class Vibration resistance Impact resistance Communication interface Power supply Power consumption Operating temperature Storage temperature Power supply Cable length System requirement USB SOFTWARE With the free basic software tool the measuring values ca be read out and saved in an excel or csv file. • • • • • • • Up to 8 gauges can be connected Easy to operate and setup Comparator...

ACCESSORIES DT SERIES Feeler Set DZ5100: 1. Off-center contact point: ø1,0 mm steel ball 2. Flat carbide contact point ø 6,5 mm 3. Plastic ball contact point ø3,0 mm, nylon ball 4. Pin contact point ø1,5 mm Tastkopf-01: steel (standard) Taskopf-01-HM: cemented carbide Tastkopf-01-R: ruby Tastkopf-01-K: ceramics Tastkopf-02: steel Tastkopf-02-HM: cemented carbide * Material of the feeler balls: steel: for standard applications ruby: much harder and wear resistant than steel, non-conductive, for all applications except for measuring on aluminium and cast iron ceramics: comparable to ruby,...

ACCESSORIES DT SERIES Airlifter DZ176 Measuring range Digital gauge Working temperature Storage temperature Mode of operation: - Use an air tube with an outer diameter of 4mm. - The supply air should be cleaned by using a filter. - Without the airlifter a spring inside of the sensor pushes the rod outwards. - With the airlifter installed the rod will be pulled inside by a stronger spring inside of the airlifter. - When air is supplied the rod will be pushed out again and the measurement can begin. - The rod retraction speed can be adjusted by the speed controller mounted on the DZ176. life...

DISPLAYS LT10A Suitable gauges Standard (without interface) Working temperature Storage temperature Key Features • Resolution : selectable • Suitable for panel mounting • Direct interfacing from display unit to PLC or computer • Current values, maximum, minimum, peak-to-peak values and GO/NO GO evaluation included as standard functions. • ADD/SUB function (2-channel model) • Full lineup for various applications Connection cable DZ252 for LT Display with RS232 interface for connection to a PC, RS232 card, etc. DZ252 cable for RS232C (for LT and U series), round 8-pin male <─> D-sub 9-pin...

ORDER CODE DIGITAL GAUGE DT12 Spring push out, IP40 Spring push out, IP64 Spring push out, IP40 Spring push out, IP64 Pneumatic push out, IP40 Pneumatic push out, IP64 Spring push out, IP40 Spring push out, IP64 without interface BCD-interface RS232C-interface Resolution 1 µm Resolution 5 µm Resolution 10 µm ORDER CODE DISPLAY LT10A without interface BCD-interface RS232C-interface ORDER CODE INTERPOLATOR MT30 ACCESSORIES Accessories Connection cable RS232 cable (for LT..C Display), Sub-D connector 1 m, high flex extension cable Standard (included in delivery) 3 m, high flex extension cable...

Subject to change without prior notice. eddylab GmbH Ludwig-Ganghofer-Str. 40 83624 Otterfing E-mail info@eddylab.de Internet www.eddylab.de