Catalogs >
eddylab GmbH >
eddy current sensors T14/T20/T40

eddy current sensors T14/T20/T40
8Pages

Catalog excerpts

T14/T20/T40 EDDY CURRENT PROBES ■ contactless distance measurement due to non-contact measuring principle for measuring ranges up to 45 mm ■ highest precision in difficult industrial environments ■ resistant to contamination, high temperatures and pressure ■ high temperature stability ■ robust

Open the catalog to page 1

2 TECHNICAL DATA SENSORS | T14/T20/T40 TECHNICAL DATA − SENSORS measurement range extended [mm]* housing size offset gap (blind range) resolution reg. corner frequency [% FS]** 10 Hz 100 Hz 1 kHz 10 kHz 35 kHz temperature range sensor temperature coefficient sensor sensor cable PTFE-COAX ø2,5 mm (max. 2,7 mm), extension cable with LEMO connector required cable length min. bend radius static/dynamic temperature range cable multipole female LEMO connector protection class shock check resistance [Ω] housing material 9 PPS/PPSU (sensor housing), stainless steel 1.4305 (back cover) * Linearity...

Open the catalog to page 2

TECHNICAL DRAWINGS − SENSORS Oberfläche / surface Gewicht / weight Name / title Name / name Werkstoff / material Maßstab / scale Allgemeintoleranz / general tolerances Zeichnungsnr. / number Verwendungsbereich / type Blatt / page Allgemeintoleranz / general tolerances 9,5 Maßstab / scale Gewicht / weight Oberfläche / surface Name / name Datum / date author appr. Name / title Zeichnungsnr. / number Verwendungsbereich / type Allgemeintoleranz / general tolerances Maßstab / scale Gewicht / weight Werkstoff / material Name / title Blatt / page

Open the catalog to page 3

CABLE CONFIGURATION The sensors are supplied with a multipole female LEMO connector as standard. For connection to the TX-Driver a cable with BNC connector is required. Optionally the cable are equipped with a SMB connector. The SMB connection is performed as BNC/SMB adaptor. Please note: The connector housing has an outer diameter of 6.5 mm. This facilitates the installation in particular with narrow conditions. If the cable is durably affixed, it might be desirable only to remove the probe from the entire cable. It is recommended to avoid unnecessary connections within the cable as it...

Open the catalog to page 4

EDDY CURRENT BASIC MODULE TX The processor based design admits linearities less than 0.1 % – which is an exceptional feature for this sensor technology. Remarkable performance allows highly dynamic measurements with 124 kSa/s. The TX-Driver is available as single- or dual-channel device. As standard, the device provides a USB and a CAN-bus Interface. The power supply is a galvanically isolated wide input from 10.5..36 (27) VDC. All available sensor heads can be connected with the basic module TX. ■ Probe and analogue output: Wide-Input-supply 10,5...36 (27) VDC, screwable M12 connector for...

Open the catalog to page 5

Choose a dry location, preferably with a stable temperature for the electrical installation (TX-Driver) such as electrical cabinets, terminal boxes, housing, etc. Connect the supply line, probe lines and output lines. Please ensure that all supply and signal lines are laid separately from energy-carrying lines such as supply and discharge lines from converters and drives, lines from ovens and synchronised appliances or generator lines, etc., in order to avoid malfunctions in the signal behaviour. Please use shielded supply lines only and apply the shield to one side to avoid ground loops....

Open the catalog to page 6

ORDER CODE ■ SENSOR probe type a according to technical drawings, (e. g., T14, T20, T40) ■ CONNECTION CABLE CONNECTION CABLE STANDARD LEMO.0T-KOAX-3M LEMO.0T-KOAX-6M LEMO.0T-KOAX-9M LEMO.0T-KOAX-12M LEMO.0T-KOAX-15M OPTIONAL CONNECTION CABLE + BNC/SMB-ADAPTOR LEMO.0T-KOAX-3M-SMB LEMO.0T-KOAX-6M-SMB LEMO.0T-KOAX-9M-SMB

Open the catalog to page 7