MAGNESCALEdigital gauge Magnescale - Measurement ranges: 12,32 mm (DT Series) - Measurement ranges: 12, 30, 60 mm (U Series) - Resolution up to 1 pm - Linearity up to 2 pm - Output signal A/B, TTL-Linedriver, EIA-422 with MT14 - USB (2.0 FS) interface with MT30 - free evaluation soft ware for download - Protection class up to IP64 - Spring loaded and pneumatic versions - Resistant against water and oil - Life cycle up to 30 million strokes

DIGITAL GAUGES DT12, DT512 Model Measurement range Resolution depending on the unit to be connected: 1 channel displays (e.g. LT10A-105): 100 / 2 channel displays (e.g. LT11A-201): 80 Spring push-out Reference point Working temperature Storage temperature Measuring force Protection class * Life cycle Steel ball tip ø3 mm, screw M2,5 Cable length compatible display *Excluding the interpolation box and connector DT12N, DT512N

DIGITAL GAUGE DT32 Model Measurement range Linearity (20°C) Displacement speed max. depending on the unit to be connected: 1 channel displays (e.g. LT10A-105): 100 / 2 channel displays (e.g. LT10A-205): 80 spring push-out Pneumatic push Reference point spring push-out Pneumatic push Working temperature Storage temperature Measuring force Protection class * Weight *Excluding the interpolation box and connector Steel ball tip ø3 mm, screw M2,5 compatible display Feeler Cable length

INSTALLATION INSTRUCTION Mounting method using mounting hole Mounting method using holder Mounting holder dimensions and tolerance

INTERPOLATOR MT14 Using the interpolator unit MT14 the digital gauges of the series DT12, DT32 and DT512 can directly be connected to PLCs etc. MT14 Resolution Output signal Voltage-differential line driver output (compliant with EIA-422) Working temperature Storage temperature 1.2 (when output load of 120 Ω is connected) Cable color 0 V and the shield (FG) are connected with a capacitor. Phase difference for phase A/B output in depending on the displacement speed v [m/min] MT14-01 * An alarm is output at a traveling velocity of 100 to 115 m/min. The sampling frequency of the

Using the interpolator unit MT30 the digital gauges DT12, DT32 and DT512 can be connected to the USB port of a PC. With the free basic software tool the measuring values ca be read out and saved in an excel or csv file. • Up to 8 gauges can be connected • Easy to operate and setup • Comparator function • Calibration (Reset) function • Scaling function • Available in various languages • Compatible with Windows 7/8/10 (XP possible)

DIGITAL GAUGE U Model MR when using air release DZ173 Display Displacement speed maximal LCD Display, 6 digits, minus display [m/s] Reference point Working temperature Storage temperature 6 VDC ±10 % (with DC IN jack) 6 to 9 VDC ±10 % (with data connector used) Supply * Consumption Feeler Weight Carbide ball tip, Mounting screw M2.5 [g] appox. 230 Instruction Manual, lift lever, and dedicated spanner * Power supply unit AC-K02 please order separately

ACCESSORIES DT SERIES Feeler Set DZ5100: 1. Off-center contact point: ø1,0 mm steel ball 2. Flat carbide contact point ø 6,5 mm 3. Plastic ball contact point ø3,0 mm, nylon ball 4. Pin contact point ø1,5 mm Tastkopf-01: steel (standard) Taskopf-01-HM: cemented carbide Tastkopf-01-R: ruby Tastkopf-01-K: ceramics Tastkopf-02: steel Tastkopf-02-HM: cemented carbide * Material of the feeler balls: steel: for standard applications ruby: much harder and wear resistant than steel, non-conductive, for all applications except for measuring on aluminium and cast iron ceramics: comparable to ruby, best...

Measuring range - The supply air should be cleaned by using a filter. - Without the airlifter a spring inside of the sensor pushes the rod outwards. - With the airlifter installed the rod will be pulled inside by a stronger spring inside of the airlifter. - When air is supplied the rod will be pushed out again and the measurement can begin. - The rod retraction speed can be adjusted by the speed controller mounted on the DZ176. Lift lever DZ161 (included in delivery)

DISPLAYS LT10A Suitable gauges Standard (without interface) Working temperature Storage temperature Key Features • Resolution : selectable • Suitable for panel mounting • Direct interfacing from display unit to PLC or computer • Current values, maximum, minimum, peak-to-peak values and GO/NO GO evaluation included as standard functions. • ADD/SUB function (2-channel model) • Full lineup for various applications Connection cable DZ252 for LT Display with RS232 interface for connection to a PC, RS232 card, etc. DZ252 cable for RS232C (for LT and U series), round 8-pin male <─> D-sub 9-pin female...

ORDER CODE DIGITAL GAUGE N P ORDER CODE DISPLAY ORDER CODE INTERPOLATOR MT30- Resolution 1 ^m Resolution 5 ^m Resolution 10 ^m ACCESSORIES Accessories USB-extension cable CE38-01 1 m, USB

Subject to change without prior notice. eddylab GmbH Ludwig-Ganghofer-Str. 40 83624 Otterfing E-mail [email protected] Internet www.eddylab.de