■ ■;' \ ■ ' \V s1 v £>■> ' l % § eckerle Condensate removal pump

Condensate pumps in air conditioning technology Condensation is the change of state of the physical state of matter from gas phase into liquid phase and is the reverse of vaporisation. It can also be defined as the change in state of water vapour to liquid (water) when in contact with any surface (evaporator coil). Condensation occurs under certain conditions relating to temperature and pressure. When gravity drainage is not possible or is impractical, condensate removal pumps are necessary to evacuate water to a drain point above the collection tray. Eckerle pumps are fully-automated and are...

D swiss drive inside Mini-Condensate Pump Usage This float type pump is mainly used in air conditioners with a limited space inside, e. g. wall mounted mini split and ceiling units. The small sensor can easily be adapted to the air conditioner’s condensate drain hose. Having the same dimensions as EE1000/EE2000 models, the EE1800 can offer a higher flow rate - due to its optimised drive inside. The pump is capable for air conditioners up to 20 kW. Description The EE1800 system consists of a pump unit and a separate 3-level float switch sensor. Beside the on/off function the system offers a high...

TATTOO 10 Design Condensate Pumpwith cable connection For air conditioners up to 10 kW Made in Switzerland Application Design meets functionality. Due to the softer plastic that is in the “tribals design” integrated in the housing, oscillations from the drive and the pulsation of the water column transferred to the housing are reduced. Active noise reduction through modern design and innovative technology. Description The Tattoo 10 and 16 consist of a single pump and float module. The three-stage float switch controls the pump. If the maximum permissible condensate level is exceeded, the float...

Usage This compact unit with integrated float switch is designed to be used inside devices equipped only with a condensate collecting tank such as fan convectors, cabinet models, built-in units, water collection consoles etc. Steps must be taken to ensure that no fluid runs over the pump! Description The delivery system is equipped with 2 separately operating float switches. The working float switch turns the pump on and off depending on the filling level (with run-on time). The function of the alarm float switch is to isolate the break contact element. □ swiss drive inside Technical Data (L...

Fan Controller Usage: The EFC Fan Controller is suitable for all air cooled condensing units in air conditioning and refrigeration units with fan motor max. currents up to 2 A resp. 4 A (ohmic load). Description: The controller provides not only the correct speed for the outdoor fan, it also determines whether the fan should stop and for how long, to give an optimum control to the system. Furthermore the control prevents over condensing even with outdoor temperatures down to -20 °C and no iced-up Indoor coils. Due to decreased compressor running time, a higher efficiency will be achieved. Intelligent...

PVC hose for EE150, EE300, EE400M, 50 m roll, inner-Ø 8 × 2 mm Float detector for EE600, EE1800, EE1000, Tattoo, EE900M Operating points*: Alarm: max. 23 mm Start: 20 ±1 mm Stop: 15 ±1 mm Sensor with 3 m cable for EE900M Hose connector (straight), Ø 6 mm Hose connector (straight), Ø 8 mm *Measurements from mounting

Eckerle offers you three different pump systems Usually found in two-part systems or split-systems such as the EE600, EE1800, EE1000/EE2000, EE1200K, EE1750 M and Tattoo, but also used in certain tank pumps such as the EE1650M in order to achieve higher lifting heights. Most Eckerle electromagnetic pumps have non return “duckbill valves”, whose large bore ensure that they are significantly less sensitive to dirt. Almost all tank pumps are equipped with this robust technology, for example the EE150, EE300 und EE400M/EE400M P. The main features of this volumetrically wide-open displacement device...