Catalogs >
EATON >
SMS IP: high voltage sealed plastic connector

SMS IP: high voltage sealed plastic connector
8Pages

Catalog excerpts

SMS IP: high voltage sealed plastic connector - 1

SMS IP: high voltagesealed plasticconnector A connector designed for indoor railway equipments, using the standard Safe ■ Finger proof High operating voltage up to 500 V Compliant to fire and ■ CEN/TS 45-545 Easy to handle ■ 1 stainless steel latch Designed for railways ■ NF F 61-030 derivated

Open the catalog to page 1

SMS IP: high voltage sealed plastic connector - 2

SMS IP Series | SOURIAU on the railway market Safety The SOURIAU solution offers a wide range of connector layouts providing a simplified process from purchasing to harnessing: 1 type of contact to order, to manage, to stock, to crimp for a wide range of connectors. SOURIAU’s standardisation policy is the best compromise between technology and cost. SOURIAU connectors ensure the continuity of the network with railway qualified connectors integrating new technologies: copper contacts, Quadrax and fibre optics to transfer high speed Ethernet and other data protocols. SOURIAU, along with its...

Open the catalog to page 2

SMS IP: high voltage sealed plastic connector - 3

SMS IP Series | Technical features (NF F 61-030 derivated) Mechanical • Plug & receptacle: black thermoplastic • Grommet & interfacial seal: light grey silicone • Locking system: 1 metallic latch - Audible "Click" • Latch: stainless steel • Keying system: 3 different positions • Fire resistance, toxicity & smoke opacity: R23/HL3 following CEN/TS 45-545 I3/F2 2 following NF F 16-101/16-102 • Current rating per contact: 15 A maxi • Operating voltage: ≤ 500 Vdc / ≤ 380 Vac following NF F 61-030 500 Vdc/ac following EN 50-124-1 • Creepage distances (unmated): > 12 mm • RoHS: compliant • Damp...

Open the catalog to page 3

SMS IP: high voltage sealed plastic connector - 4

SMS IP Series | Dimensions & weight Plug Part number * weight of the connector without contact

Open the catalog to page 4

SMS IP: high voltage sealed plastic connector - 5

SMS IP Series | Assembly instructions 7.1 mm Crimp contacts on wires • Strip each wire to the lenght indicated. Manual crimp pliers Selector set-up - Wire section Contact insertion • Locate the right cavity and use a contact (male or female), to bore each individual grommet in its center. Push the contact until mechanical stop. • Check the correct contact retention by slightly pulling on the cable (no tools required). • Check that each individual grommet is correctly plated on the back face of the connector, unless, put them properly. Once all the contacts have been installed in the...

Open the catalog to page 5

SMS IP: high voltage sealed plastic connector - 6

SMS IP Series | Receptacle coding Connectors are supplied with coding pins, ensure to remove these pins before using the connectors. • Coding is done by 1 or 2 pins depending on the layout (see page 7). Pins under the receptacle Pins under the plug and the sides • Pre-locate the pin into the correct cavity depending on the choosen coding (see Coding configuration). • Push the pin with the contact insertion tool (RX2025GE1) until mechanical stop. The outside height must be 5mm maxi. Unscrew the tip of the tool • Push the pin with the contact insertion tool (RX2025GE1) without its tip until...

Open the catalog to page 6

SMS IP: high voltage sealed plastic connector - 7

Coding configuration

Open the catalog to page 7

SMS IP: high voltage sealed plastic connector - 8

SMS IP Series | Fixing the connectors Rear panel mount fixing (Panel cut out dimensions page 4) • Initially place the nut in its cavity. The nut must be placed correctly so that it cannot turn in its cavity. • Introduce the receptacle by the rear panel and tighten the 2 screws (washers can be added). The recommended tightening torque is: 1.7N.m maxi with M3 stainless steel screws. Flat board receptacle fixing (Fixation points defined page 4) • Place the receptacle on the flat board and tighten the 2 screws (washer can be added). The recommended tightening torque is: 1.7N.m maxi with M3...

Open the catalog to page 8

SMS IP: high voltage sealed plastic connector 8Pages

Catalog excerpts

All EATON catalogs and technical brochures

SMS IP: high voltage sealed plastic connector
8Pages