Eaton Servo-Performance Proportional Directional Valve AxisPro F^T’N Powering Business Worldwide

Introduction General Description Typical Section View 3 Spool Sleeve Details 5 AxisPro™ is a game changing machine control valve. Its embedded intelligence simplifies traditionally complex control practices. Plug and play design reduces machine build time, and its ability to predict potential maintenance issues increases machine reliability. AxisPro level 2 KBH valves, can be used to control machine motion in open or closed loop control applications. The valve can receive its analog command input on the 7-pin connector from an external axis control device or, with the available on-board...

General Description Unique benefits from AxisPro Built on the proven KBH servo Proportional Valve technology, Eaton’s new AxisPro Proportional Valve provides a range of controls capability in a modular design. These solenoid operated proportional valves offer high dynamic performance which enables them to be used in closed-loop control applications. The LED lens is standard on all AxisPro valves and provides a quick easy way to visually determine if AxisPro has detected any system warnings or faults. Detailed health, valve performance and warning/fault data is easily accessible via Eaton’s Pro-FX...

Model Code KBH – wo stage servo T performance proportional valve with integral amplifier and electronic feedback 2  1 Level 1 3   Interface 07 – ISO 4401, Size 8 4   Spool/Sleeve Size 8 01 – C230N - overlapped, 2 P,A,B,T blocked 02 – C230N - zero lapped; 5 P,A,B,T blocked 03 – 3C230N - P blocked, A 3 & B to tank 04 – C230N140 2 overlapped, P,A,B,T blocked, asymmetric 05 – C230N140 - zero 5 lapped, P,A, B, T blocked 06 – 3C230N140 - P 3 blocked, A & B to tank, asymmetric 07 – Q230F - Pressure flow P control spool 5   Valve Special Feature NS – Not Selected 6   Pilot Supply TS – nternal supply...

Note: Control Mode is shipped in valve spool closed loop position control (VSC) configuration. You may reconfigure to other command signal options using Pro-FX Configure 2.0 software. |~2| 2 - Level 1 plus Network enabled and DS408 control modes M Command Signal 1 - +/- 10V voltage command signal Note: Command signal is shipped with 1 configuration. You may configure to other command signal options using Pro-FX Configure 2.0 software. 2 - 4-20mA current command signal 3 - +/- 10mA current command signal 4 - +/- 15mA current command signal 5 - +/- 20mA current command signal 9 - Command over Fieldbus |~9]...

Spool Sleeve Details Main-stage spool Hydraulic symbol Description SIZE 7 Flow Symmetric ℓ∕min@ ∆10 bar Overlapped, all ports block Critically lapped Overlapped, all ports block EATON AxisPro Proportional Two-Stage Directional Valve KBH*-07 E-VLPO-TT003-E

Spool Symbols Application Notes 1. Main-Spool Options Spools shown are meter-in/ meter-out types. Center-condition options are type 5C. 2. Internally Piloted Models Differ from detailed symbols above by omission of plug A and the blocking of port X by the mating surface. 3. Internally Pilot Drain Models Differ from detailed symbols above by omission of plug B and blocking of port Y by the mating surface. Spool Types and Flow Ratings Symmetric Spools Base line pressure drop Ap 5 bar (72 psi) per metering flow path, e.g. B to T. For actual maximum flow refer to power capacity envelope curves. Note:...

Performance Curves Single flow path gain at 5 bar delta At Øp = 5 bar (72 psi) per metering (e.g.P-A), Percentage command signals applicable for P to A and negative values of command signal. positive ØpX P to BØp values, flow rates approximate to: Q = Q At other Limited by valve power capacity. Refer to curves on page 9 Øp = Pressure drop at datum flow rate where Q = Datum flow rate B to T Valve Pressure drop – bar POWER CAPACITY ENVELOPE Flow through P-A-B-T or P-B-A-T Flow rate – L/min Low flow gain at 50 bar delta 14.00 FREQUENCY RESPONSE, TYPICAL For an amplitude of 50 ± 25% of rated flow...

Performance Curves Command voltage Command voltage Command voltage EATON AxisPro Proportional Two-Stage Directional Valve KBH*-07 E-VLPO-TT003-E February 201

Connector Details 7-pin plug connector a r g B C D A Power supply positive (+) B Power supply 0V and current command return C Not connected (Field 8 = C,E) C Valve enable (Field 8 = H,R) D Command signal (+V or current in) E Command signal (-V or current GND) Note: Present at location 1 of the electronics enclosure (see figure 1 below). To ensure EMI protection use only metal shielded mating connectors. Mating 7-pin (connector) is Eaton part number 934939 *Not connected to pin A on 7 pin plug connector, need to be supplied externally M12 8-pin External Digital Sensor M12 8-pin External...

Data is typical, with fluid at 32 cST (150 SUS) and 40°C (104°F) EATON AxisPro ProportionalTwo-Stage Directional Valve KBH*-07 E-VLPO-TT003-E Februar

Operating Data KBS*-07 Valves (all valves) Relative duty factor Hysteresis Mass: kg (Ib) approx. Valves with pressure reducer Environmental 11 kg (24 Ib) approx IP65 and IP67 rated when using a similarly rated connector Location 2, 3, 4 and 5 connectors have IP65 and IP67 rated shipping covers Step response: Step, % Flow EATON AxisPro Proportional Two-Stage Directional Valve KBH*-07 E-VLPO-TT003-E February 2019

Software Information KBH2 Analog command spool control •• CANopen DSP306 compliant electronic data sheet (EDS). Analog command source configuration options •• Diagnostic configuration options. Monitor output signal configuration options •• Optional White Space Enable input signal enable/disable option •• Optional Pilot Pressure Sensors •• Sensor port configuration options. Position, Speed, Pressure, Force and SSI Sensors. All levels and models are compatible with the Eaton Pro-FX. For the latest revision, please visit www.eaton.com/AxisPro AxisPro test boxes Features: •• Power supply with wide...