Distributed By: E-Z Clip System Assembly Instructions Eaton 14615 Lone Oak Road Eden Prairie, MN 55344 USA Tel: 952 937-9800 Fax: 952 974-7722 www.hydraulics.eaton.com Eaton 20 Rosamond Road Footscray Victoria 3011 Australia Tel: (61) 3 9319 8222 Fax: (61) 3 9318 5714 Eaton Dr.-Reckeweg-Str. 1 D-76532 Baden-Baden Germany Tel: (49) 7221 682-0 Fax: (49) 7221 682-788 © 2002 Eaton Corporation All rights reserved Printed in USA Document No. A-HC-TI-0001-E Supercedes KA127 June 2002

Aeroquip Proudly Introduces... The E-Z Clip™ System The E-Z Clip System is designed for assembly with Aeroquip GH134 Multi-Refrigerant hose. Its engineered connection exceeds SAE J2064 and has been vibration and impulse tested. The benefits of E-Z Clip are virtually endless: • No guess work • No leaking crimps • No power supply needed • As easy to use as a pair of pliers • Easy to use in confined areas • NOTICE • If the pliers are not kept square during closing of the clip, the clasp may have an offset. Use the pliers to correct the clasp alignment. (incorrect) (correct) E-Z Clip components should...

E-Z STEP 7: Close the clips. Use the FT1357 pliers to close the clips. The pliers should be positioned squarely on the clip connection points and should remain square during the closing of the clip. E-Z Clip System Components Are Simple To Identify, Order, And Use. Ordering Information HOSE NIPPLE CAGE CLIPS GH134-6 1F40105-06C 1F40104-06C GH134-8 FJ___-__08S 1F40105-08C 1F40104-08C GH134-10 correct FJ___-__06S FJ___-__10S 1F40105-10C 1F40104-10C GH134-12 FJ___-__12S 1F40105-12C 1F40104-12C Identification Guide HOSE CLIPS GH134-6 -6 and 150 150 GH134-8 -8 and 175 175 GH134-10 -10 and 200 200...

E-Z Clip System Assembly Instructions E-Z STEP 4: E-Z STEP 1: Insert the nipple into the hose. To ensure that the nipple is fully inserted, check the gap between the cut end of the hose and the shoulder on the nipple. Care should be taken to avoid kinking or other damage to the hose during nipple insertion. Cut the hose. Cut the hose to proper length with an appropriate cutting tool. Aeroquip's hand-held hose cutter (FT1356) has been specially designed for cutting all non-wire reinforced hose, such as GH134 Multi-Refrigerant hose. Be sure the cut is made square to the hose length. NOTE: Be sure...

E-Z Clip System Assembly Instructions E-Z STEP 4: E-Z STEP 1: Insert the nipple into the hose. To ensure that the nipple is fully inserted, check the gap between the cut end of the hose and the shoulder on the nipple. Care should be taken to avoid kinking or other damage to the hose during nipple insertion. Cut the hose. Cut the hose to proper length with an appropriate cutting tool. Aeroquip's hand-held hose cutter (FT1356) has been specially designed for cutting all non-wire reinforced hose, such as GH134 Multi-Refrigerant hose. Be sure the cut is made square to the hose length. NOTE: Be sure...

E-Z STEP 7: Close the clips. Use the FT1357 pliers to close the clips. The pliers should be positioned squarely on the clip connection points and should remain square during the closing of the clip. E-Z Clip System Components Are Simple To Identify, Order, And Use. Ordering Information HOSE NIPPLE CAGE CLIPS GH134-6 1F40105-06C 1F40104-06C GH134-8 FJ___-__08S 1F40105-08C 1F40104-08C GH134-10 correct FJ___-__06S FJ___-__10S 1F40105-10C 1F40104-10C GH134-12 FJ___-__12S 1F40105-12C 1F40104-12C Identification Guide HOSE CLIPS GH134-6 -6 and 150 150 GH134-8 -8 and 175 175 GH134-10 -10 and 200 200...

Aeroquip Proudly Introduces... The E-Z Clip™ System The E-Z Clip System is designed for assembly with Aeroquip GH134 Multi-Refrigerant hose. Its engineered connection exceeds SAE J2064 and has been vibration and impulse tested. The benefits of E-Z Clip are virtually endless: • No guess work • No leaking crimps • No power supply needed • As easy to use as a pair of pliers • Easy to use in confined areas • NOTICE • If the pliers are not kept square during closing of the clip, the clasp may have an offset. Use the pliers to correct the clasp alignment. (incorrect) (correct) E-Z Clip components should...