Market segments The rectangular design of the Series 41 (18 x 24 mm) makes it especially suited: The Series 41 incorporates the following functions: The EAO Series 41 is especially suited for applications in the segment: Raised design PCB (with adaptor) Indicator Illuminated pushbutton The series features a compact double-lit element that can be tted from the front as a snap-on module. Please refer to the EAO website to obtain detailed information regarding this series www.products.eao.com Congure a product to your exact needs and request a quotation.

Raised design

Raised design Equipment consisting of (schematic overview) Product can differ from the current configuration. Dimensions [mm] L = Solder terminal, H = Universal terminal 2.0 x 0.5 mm Each Part Number listed below includes all the black components shown in the 3D-drawing. To obtain a complete unit, please select the red components from the pages shown. Wiring diagram Indicator, Front dimension 18 x 24 mm Solder Indicator, Front dimension 18 x 24 mm Universal 2.0 x 0.5 mm

Raised design Equipment consisting of (schematic overview) Lens Each Part Number listed below includes all the black components shown in the 3D-drawing. Dimensions [mm] L = Solder terminal, H = Universal terminal 2.0 x 0.5 mm Product can differ from the current configuration. To obtain a complete unit, please select the red components from the pages shown. Switching action Illuminated pushbutton, Front dimension 18 x 24 mm Snap-action switching element Low-level element Switching system Wiring diagram Illuminated pushbutton, Front dimension 18 x 24 mm 2 NO Contacts: NC = Normally closed, NO =...

Raised design

Lens plastic single-colour Product attribute orange transparent yellow transparent green transparent blue transparent colourless transparent orange transparent yellow transparent green transparent colourless transparent Lens plastic single-colour flat, illuminative flat, illuminative, less suitable for film insert Lens plastic bi-colour Product attribute red-orange transparent red-yellow transparent red-green transparent red-blue transparent red-colourless transparent orange-green transparent orange-blue transparent orange-colourless transparent yellow-green transparent yellow-blue transparent...

Product attribute flat, illuminative, less suitable for film insert orange-colourless transparent yellow-green transparent yellow-colourless transparent green-colourless transparent colourless-colourless transparent Protective cover, IP 40 Additional Information • Hinged, with means for sealing • Please note that bigger minimum distances are necessary • Front panel thickness reduces by 2 mm Product attribute Protective cover for button with front dimension 15 x 21 mm Blind plug Blind plug

Rear side The component layouts you will find from page 14 Flat receptacle Product attribute Flat receptacle Insulation sleeve Product attribute Insulation sleeve

LED, T1 3/4 MG Additional Information • Due to high surface temperatures, the series resistor must not be soldered directly to the terminals of the equipment (use a terminal plate) Ø 6.1 max. When using AC/DC types with AC operation, slight flickering can occure • Luminous intensity data of the LEDs on direct voltage • Electrical and optical data are measured at 25 °C • The specified versions are built with a protection diode (halve wave rectifier) in series and the LED • Luminosity and wave length variations caused by LED manufacturing processes may cause slight differences regarding the illumination...

Filament lamp, T1 3/4 MG • Order two filament lamps Operating voltage Operation current Filament lamp Series resistor Additional Information • Only for filament lamp 48 VAC, 25 mA • For lamp voltage reduction • Keep to the country specific safety instructions • Due to high surface temperatures, the series resistor must not be soldered directly to the terminals of the equipment (use a terminal plate) Operating voltage Series resistor

Terminal plate empty Product attribute Terminal plate empty

Lens remover Product attribute Lens remover Lamp remover Additional Information p Caution: A switching process might be released when replacing the lamp Lamp remover Dismantling tool

Ø2.1 hole for central mounting with M2 screw if desired

Technical data Actuator with snap-action switching element Switching system Self-cleaning, double-break, snap action switching system (with contact gap 2 x 0.5 mm). 1 normally closed or 1 normally open contact per element. Up to 4 switching elements can be on a pushbutton (max. 4 normally closed and 4 normally open contacts). Material Material of contacts gold-plated silver Switching element Soldering terminal: PA 6.6 Ultramid Actuator case Polysulfone, heat-resistant and self-extinguishing Mechanical characteristics Connection method Snap-action switching element with tinned soldering terminals...

Technical data Actuator with Low Level switching element Switching system This low level switching element was designed for switching low powers in electronic circuits. The mechanism assures reliable switching of loads ranging from a few mA / mV up to 100 mA /42 VAC/VDC. Single-break momentary contact, as normally open or normally closed with 4 independent points of contact. 2 momentary contacts per switching element; combination of normally open and normally closed is possible. Special features are the long life, extremely short rebound time and stable contact resistance. Material Actuator case...

General notes 1. Engraving Typefaces In addition to the most commonly used world languages (see DIN 1451) with close spacing, the following typefaces are available: Scandinavian, Slavian, Greek, Russian. Coloured filling of engraving Specify whether engraving should be on the diffuser, or on the lens. Specify the infill colour, character height and the text or symbol orientation. Symbols A list of the symbols available can be supplied on request. 3. Film inserts Instead of using engraving, the lenses can be fitted with transparent film inserts. For this purpose, though, it is advisable to use...