Series Characteristics The Series 10 are LEDs for use with all EAO’s illuminated switches (as accessories). The following pages show a representative selection of LEDs.

Product can differ from the current configuration. Additional Information • A suitable lamp remover Part No. 61-9740.0 (Series Swisstac Part No. 300-0002-00) • When using AC/DC types with AC operation, slight flickering can occure • Luminous intensity data of the LEDs on direct voltage • Electrical and optical data are measured at 25 °C • If the 24VDC Bi-colour lamp is driven with normal polarity (plus on middle contact of the lamp) the first mentioned colour will light up, with inverted polarity the second colour will ligth up • The specified versions are built with a protection diode (halve...

Operating voltage Operation current Lumi. intensity Single-LED blue Single-LED white

Product can differ from the current configuration. Additional Information • A suitable LED remover Part No. 02-906 (Series Swisstac Part No. 300-0002-00) • When fitting the LED elements pay attention to the polarity. An instruction can be found in the chapter «Application guidelines» of the corresponding series • When using AC/DC types with AC operation, slight flickering can occure • Electrical and optical data are measured at 25 °C • Luminous intensity data of the LEDs on direct voltage • The specified versions are built with a protection diode (halve wave rectifier) in series and the LED •...

Operating voltage Operation current Lumi. intensity Single-LED blue Single-LED white

Product can differ from the current configuration. Additional Information • A suitable LED remover Part No. 03-996 • When fitting the LED elements pay attention to the polarity. An instruction can be found in the chapter «Application guidelines» of the corresponding series • When using AC/DC types with AC operation, slight flickering can occure • Luminous intensity data of the LEDs on direct voltage • Electrical and optical data are measured at 25 °C • The specified versions are built with a protection diode (halve wave rectifier) in series and the LED • Luminosity and wave length variations...

Operating voltage Operation current Lumi. intensity Single-LED blue 48 VAC/DC +10 % Single-LED white

Product can differ from the current configuration. Additional Information • A suitable LED remover Part No. 700.006.0 (Series 44 Part No. 44-935) • Luminous intensity data of the LEDs on direct voltage • Electrical and optical data are measured at 25 °C • The specified 6 VDC, 24 VDC Bi-colour; 130 VAC, 130 DC und 230 VAC versions are built with a protection diode • The specified 12, 24, 28, 48 VAC/DC versions are built with a bridge rectifier • If the 24VDC Bi-colour lamp is driven with normal polarity (plus on middle contact of the lamp) the first mentioned colour will light up, with inverted...

Operating voltage Operation current Lumi. intensity Single-LED yellow Single-LED green Single-LED blue Single-LED white

Product can differ from the current configuration. Additional Information • A suitable LED remover Part No. 700.006.0 (Series 44 Part No. 44-935) • Luminous intensity data of the LEDs on direct voltage • Electrical and optical data are measured at 25 °C • The specified 72 and 110 VAC/VDC versions are built with a protection diode • Specified 72 and 110 VAC/VDC versions are built with a bridge rectifier • In case one LED fails, the other pair of still functioning LED›s is working. The light output then is half in order to indicate the malfunction and shows this way the need for replacement Operating...

Bridge rectifier

LED remover for T1 3/4 MG Additional Information p Caution: A switching process might be released when replacing the lamp Product attribute LED remover for T5.5 Additional Information p Caution: A switching process might be released when replacing the lamp Product attribute LED remover for T6.8 Additional Information p Caution: A switching process might be released when replacing the lamp Product attribute

LED remover for BA9s Additional Information p Caution: A switching process might be released when replacing the lamp Product attribute

Technical data Technical Data Electrical characteristics Environmental conditions Operating voltage tolerance +10 % Mechanical characteristics EAO reserves the right to alter specifications without further notice.

Application guidelines LED used in Base Series

Index from Part No. Part No.