TELEDYNE e2VEverywhereyoulook"UNiiQA+ Mono cl CMOS MONO CAMERA Datasheet Features ■ CMOS Monochrome LineScan Sensors: • 4096 pixels, 5x5pm or 4096 pixels, 5x10pm (Versatile models Only) • 2048, 1024 or 512 pixels, 10x10pm ■ Interface : CameraLink® (Base or Medium/Full) ■ Line Rate : • Up to 40 kl/s for the Base Version • Up to 100 kl/s for the High-Speed Version • Line rate limited at 40kl/s in 12bits for all models ■ Data Rate : • 42.5MHz, 60MHz and 85MHz in 1 or 2 Channels for Base version • 42.5MHz, 60MHz and 85MHz in Base, Medium, Full or Full+ (Deca) for the High Speed Version ■ Bit Depth : 8, 10 or 12bits ■ Flat Field Correction ■ Contrast Expansion ■ Power Supply : 10 - 15V. PoCl Compliant. ■ Low Power Consumption : < 3.5W ■ M42x1 Native and F-Mount, C-Mount adapters available ■ GenCP Compliant (xml file embedded) Description e2v's UNiiQA+ line scan cameras family has been specifically designed to overcome the limitations of your current inspectioi system: make cost savings, improve your throughput, inspect larger areas or identify smaller defects. Three UNiiQA+ product ranges are offered: ■ UNiiQA+ Essential: low speed cameras for cost effective equipment or with modest speed requirement ■ UNiiQA+ High-Speed: high speed cameras to help improve the performance of your system The UNiiQA+ family has also been designed to be highly modular to enable engineers to reuse the same camera in multiple equipment, simplify logistics and reduce development cycle time. All UNiiQA+ cameras feature e2v's proprietary CMOS sensors : a single line of highly sensitive pixels of either 5pm or 10pm size. Application ■ Raw material inspection (plastic film, glass, wood...) ■ Print and paper inspection ■ Food sorting (Belt sorting, Lane sorting, Free fall sorting) ■ Parcel and postal sorting ■ Barcode reading

TELEDYNE e2VEverywhereyoulook™Key Specifications Characteristics *** Versatile Models Only Notes: (*) High Dynamic / High Response.: High dynamic with the Use of Multi-Column Gain 1/2 (**) e2vnorm: more severe than EMVA 1288 Standard

TELEDYNE e2VEverywhereyoulook™ Functionality (Programmable via Control Interface) Image Sensor The Uniiqa+ sensor is composed of one pair of sensitive lines of 4096 pixels of 5pm square. Each pixel on the same column uses the same Analog to Digital Column converter (ADC Column). This structure allows several definitions : ■ 4k pixels 5x5pm ■ 2k Pixels 10x10pm by binning of 4 pixels ■ Then, 1k or 0,5k 10x10pm are achieved by applying an ROI on the centre of the sensor. Memory Node

Response & QE curves Quantum Efficiency Spectral Response Curves (*) High Dynamic / High Response. : High dynamic with the Use of Multi-Column Gain 1/2

Camera Hardware and Interface DSC UNIIQA+ CL Monochrome 05/2017 Page | 5

TELEDYNE e2VEverywhereyoulook”Input/output Connectors and LED USB Connector For Firmware upgrade Power Connector Camera connector type: Hirose HR10A-7R-6PB (male) Cable connector type: Hirose HR10A-7P-6S (female) The Camera is compliant PoCl (Power Over Camera Link) : The Power Connector is not used if the Frame Grabber can be also compliant PoCL

TELEDYNE e2VEverywhereyoulook”CameraLink Output Configuration NR : Not required as the fastest speed (100kHz) is already achieved by the precedent output mode with the lowest data rate (ex : 100kHz is achieved on 512 pixel in base mode with 2 x 42.5Mhz. Medium is not required, even for 10bits.

Standard Conformity The UNIIQA+ cameras have been tested using the following equipment:  A shielded power supply cable  A Camera Link data transfer cable ref. 1MD26-3560-00C-500 (3M), 1SF26-L120-00C-500 (3M)  A linear AC-DC power supply e2v recommends using the same configuration to ensure the compliance with the following standards. CE Conformity The UNIIQA+ cameras comply with the requirements of the EMC (European) directive 2004/108/EC (EN 50081-2, EN 61000-6-2). FCC Conformity The UNIIQA+ cameras further comply with Part 15 of the FCC rules, which states that: Operation is subject to the...