EE10
3Pages

Catalog excerpts

YOUR PARTNER IN SENSOR TECHNOLOGY ELEKTRONIK® Ges.m.b.H EE10 Humidity and Temperature Room Sensors EE10 is dedicated for accurate relative humidity (RH) and temperature (T) measurement in residential and commercial HVAC. The RH and T measured data is available either on two analogue outputs, or on a BACnet or Modbus RTU interface. A version with analogue RH and passive T output is also available. The measured data corresponding to the active outputs can be read locally on the optional display. Additional physical quantities are available on the Modbus RTU and BACnet MS/TP interface: absolute humidity, mixing ratio, enthalpy, frost point temperature and water vapor partial pressure. The stylish enclosure is available in several colors and in two sizes according to regional standards. The back cover, which contains only the screw terminals, can be mounted and wired first. The front cover containing the electronics can be simply snapped onto the back cover right before commissioning. Thus the active part of the device is not exposed to construction site pollution and can be replaced without tools within seconds. Typical Applications Building automation Indoor climate control Technical Data Features High accuracy and long term stability Fast and easy installation Modbus, BACnet or analogue outputs Measured values Relative Humidity Working range 0...95 % RH Temperature dependence typical 0.06 % RH /°C (0.03 % rh / °F) Accuracy^ at 20 °C (68 °F) and UV=24 V DC output A3: ±0.25 °C (±0.45 °F) output A6: ±0.4 °C (±0.72 °F) (RH: 0...100 % RH / T: see ordering guide) 4-20 mA (two wires) RL < (Uv-10)/0.02 < 500 Ohm Digital Interface RS485 with max. 32 devices on one bus Protocol Modbus RTU or BACnet MS/TP Temperature passive please see ordering guide for DC supply: typ. 4 mA / for AC supply: typ. 15 mAett for DC supply: typ. 9 mA / for AC supply: typ. 20 mA screw terminals max. 1.5 mm2(awg 16) US Version: UL94V-0 approved / EU Version: UL94HB approved IP30 for EE10-M1 Humidity / Temperature alternating General Voltage supply (UV) 0 - 10 V 4 - 20 mA RS485 Current consumption Analogue (0-10 V, 4-20 mA) Digital (RS485) Electrical connection Housing (polycarbonate) Protection class Display Temperature working range -5...55 °C (23...131 °F) Temperature storage range -25...60 °C (-13...140 °F)

Open the catalog to page 1

Connection Diagram Connected on the electronics board. The bus address can be set with DIP-Switches on the electronics board. Screw terminals appropriate for daisy-chain wiring Colour: EU-Standard, US: Front cover: signal white RAL9003 Back cover: light grey RAL7035 EU-Grey: Front and back cover: anthracite grey RAL7016 EU-Silver: Front and back cover: white aluminum RAL9006 Scope of Supply - EE10 Sensor according to ordering guide - Mounting materials - Test report according to DIN EN10204 - 2.2 - Quick user guide (for digital output only) v3.1 / Modification rights reserved

Open the catalog to page 2

ELEKTRONIK® Ges.m.b.H Model Humidity + Temperature Humidity + Temperature passive Display without display with display Protocol Modbus RTU3) BACnet MS/TP4) P1 P3 Unit metric-SI non-metric Baud rate 9600 (usual for Modbus) 19200 38400 (usual for BACnet) 576005) 768005) 1) Only with output A3 and A6. T sensor details 2) -5 °C (23 °F) < Scale T low < 20 °C (68 °F). 3) Factory setting: Even Parity, Stopbits 1. 4) Factory setting: No Parity, Stopbits 1. 5) Only for BACnet MS/TP at www.epluse.com/R-T_Characteristics. For other passive T sensors please contact E+E. 25 °C (77 °F) < Scale T high <...

Open the catalog to page 3