DYNISCO MODELS PT130, PT140, PT150 & PT160 Hydraulic Pressure Transducers for Injection Molding Applications Description The Dynisco PT100 series measures hydraulic pressure on injection molding machines. The PT100 series withstands cyclic pressure and provides outstanding performance under the severe demands of measuring the injection ram and clamp pressure of injection molding machines. Variations in the hydraulic pressure profile indicate irregularities during the injection and feeding stages of the molding operation and provide information about the stability of the injection ram system. Features Benefits • Stainless steel construction • Contoured diaphragm • Rugged • Greater accuracy, repeatability, fatigue strength • Easy set-up • Internal shunt calibration (PT130, PT150, PT160) • Potted hybrid electronics and flex-print wiring • 3 mV/V, 5 Vdc, 10 Vdc or 4 to 20 mA outputs • Fully temperature compensated • Ranges from 0 - 500 psi to 0 - 10,000 psi • • • • Resists shock and vibration Choice of outputs Ideal for high temperature processes Choice of ranges Specifications Performance Characteristics Ranges (psi): 0 - 500, 0 - 750, 0 - 1,000, 0 - 2,500, 0 - 3,000, 0 - 5,000, 0 - 10,000 Accuracy: ± 0.5% full scale including linearity, hysteresis and repeatability Safe overpressure: 2 x rated pressure Burst pressure: 5 x rated pressure Full scale output: PT130: 3 mV/V ±1.0% typical (±2.0% maximum) PT140/150/160: 5 Vdc, 10 Vdc, 4 to 20 mA ±1.0% typical (±2.0% maximum) Zero balance: ±1.0% typical (±2.0% maximum) Electrical Characteristics Input resistance: PT130: 420 Ohms ±10% Output resistance: PT130: 370 Ohms ±10% Load resistance: PT150/160: 2,000 Ohms minimum Maximum loop resistance: PT140: 0 to 1,100 Ohms from 14 to 36 Vdc Internal shunt calibration (R-Cal): PT130/150/160: 80% ±0.5% full scale typical (±1.0% maximum) Wiring: Reverse polarity protection of excitation leads Output: 3 mV/V 0 to 5 Vdc (4 - wire) 1 to 6 Vdc (3 - wire) 0 to 10 Vdc (4 - wire) 1 to 11 Vdc (3 - wire) 4 to 20 mA (2 - wire) Input voltage: 10 Vdc recommended, 15 Vdc maximum 11 to 32 Vdc, ±12 to ±16 Vdc 11 to 32 Vdc 16 to 32 Vdc, ±14 to ±16 Vdc 16 to 32 Vdc 14 to 36 Vdc Temperature Characteristics Operating range: PT130: -65°F to +250°F (-54°C to +120°C) PT140/150/160: -20°F to +185°F (-29°C to +85°C) Compensated range: 0°F to +150°F (-18°C to +66°C) Temperature effect on zero: PT130: ±0.005% full scale/°F (±0.009% full scale/˚C) typical (±0.01%/±0.018% maximum); PT140/150/160: ±0.02% full scale/˚F (±0.036% full scale/°C) Temperature effect on span: ±0.02% full scale/°F (±0.036% full scale/˚C) Mechanical Characteristics Wetted material: 17 - 4 PH, 15 - 5 PH stainless steel Cover material: 303, 304 stainless steel 182 Weight: Approximately 5.5 ounces

DYNISCO MODELS PT130, PT140, PT150 & PT160 Hydraulic Pressure Transducers for Injection Molding Applications BENDIX CONNECTOR PT02A-10-6P (OR EQUIVALENT) MATING CONNECTOR PT06A-10-6P (OR EQUIVALENT) 1/8-27 NPT Ø 1.375 (34.93) .47 .43 ( 11.94 ) 10.92 Ø 1.00 (25.4) DIM K .88 (22.4) FLATS DIM L Model Pressure Range Dim K Dim. L PT130, PT150, PT160 500 - 10,000 .55 (13.97)/.49 (12.45) 2.55 (64.77)/2.48 (62.99) PT140 500 - 10,000 .58 (14.73)/.52 (13.21) 3.78 (96.01)/3.71 (94.23) All dimensions are in inches (millimeters) unless otherwise specified Connector Wiring Ordering Guide Model Pressure Range...