DuPont™ Tyvek® IsoClean® , Model IC 183 B WH DS
8Pages

{{requestButtons}}

Catalog excerpts

DuPont™ Tyvek® IsoClean® , Model IC 183 B WH DS - 1

Technical data sheet DuPont™ Tyvek® IsoClean® , Model 1C 183 B WH DS Product Description DuPont™ Tyvek® IsoClean® unhooded coverall model IC 183 B WH DS. Clean-processed and gamma-sterilized. Bound internal seams. Tunnelled elastication at wrists and ankles. Elasticated waist at back. Tyvek® covered elasticated thumb loops. Zipper closure. Storm flap. Aseptically folded. CE-certified. White. • Certified according to Regulation (EU) 2016/425 • Chemical protective clothing, Category III, Type 5-B and 6-B • EN 14126 (barrier to infective agents), EN 1073-2 (protection against radioactive contamination) 25 per box, individually double packed. 2 polyethylene liners. Cardboard box. • Clean-processed and sterilised by gamma-irradiation to SAL of 10-6 (ISO 11137-1) • Full traceability on all sterilized apparel with certificates of sterility available • Suitable for use in GMP class A/B (ISO Class 5) clean rooms Size Article Number Chest Girth(cm) Body Height(cm) Chest Girth(in) Body Height(ft/in) Technical_Description _ 101020 _ EN .pdf Printed on : July 30, 2018 page 1 of 8

Open the catalog to page 1
DuPont™ Tyvek® IsoClean® , Model IC 183 B WH DS - 2

1 According to EN 14325 3 According to EN 1073-2 12 According to EN 11612 13 According to EN 11611 5 Front Tyvek ® / Back 6 Based on test according to ASTM D-572 7 See Instructions for Use for further information, limitations and warnings 11 Based on the average of 10 suits, 3 activities, 3 probes > Larger than < Smaller than N/A Not Applicable * Based on lowest single value Technical_Description _ 101020 _ EN .pdf Printed on : July 30, 2018 page 2 of 8

Open the catalog to page 2
DuPont™ Tyvek® IsoClean® , Model IC 183 B WH DS - 3

Property Test Method Result EN Class Air Permeability (Gurley method) ISO 5636-5 Yes N/A Air Permeability (Gurley method) ISO 5636-5 4 s N/A Water Vapour Resistance, Ret EN 31092/ISO 11092 6.8 m2*Pa/W N/A Thermal Resistance, clo value EN 31092/ISO 11092 0.065 clo N/A 2 According to EN 14126 5 Front Tyvek ® / Back > Larger than < Smaller than N/A Not Applicable Penetration and Repellency Property Test Method Result EN Class Resistance to Penetration by Liquids, Sulphuric Acid (30%) EN ISO 6530 <1 % 3 of...

Open the catalog to page 3
DuPont™ Tyvek® IsoClean® , Model IC 183 B WH DS - 4

Carboplatin (10mg/ml) Carmustine (3.3 mg/ml, 10 % Ethanol) Cisplatin (1 mg/ml) Cyclophosphamide (20 mg/ml) Doxorubicin HCl (2 mg/ml) Etoposide (Toposar®, Teva) (20 mg/ml, 33.2 % (v/v) Ethanol) Fluorouracil, 5- (50 mg/ml) Gemcitabine (38 mg/ml) Ifosfamide (50 mg/ml) Oxaliplatin (5 mg/ml) Paclitaxel (Hospira) (6 mg/ml, 49.7 % (v/v) Ethanol) Thiotepa (10 mg/ml) Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid Liquid BT Act (Actual) Breakthrough time at MDPR [mins] BT 0.1 Normalized breakthrough time at 0.1 ^g/cm2/min [mins] BT 1.0 Normalized breakthrough time at 1.0...

Open the catalog to page 4
DuPont™ Tyvek® IsoClean® , Model IC 183 B WH DS - 5

Important Note The permeation data published have been generated for DuPont by independent accredited testing laboratories according to the test method applicable at that time (EN369, ASTM F739, EN 374-3, EN ISO 6529 (method A and B) or ASTM D6978) The data is typically the average of three fabrics samples tested. All chemicals have been tested at an assay of greater than 95 (w/w) % unless otherwise stated. The tests were performed at room temperature and environmental pressure unless otherwise stated. A different temperature may have significant influence on the breakthrough time....

Open the catalog to page 5
DuPont™ Tyvek® IsoClean® , Model IC 183 B WH DS - 6

Permeation Data for Tyvek® IsoClean® CS Hazard Name Physical State BT Act (Actual) Breakthrough time at MDPR [mins] BT 0.1 Normalized breakthrough time at 0.1 µg/cm²/min [mins] BT 1.0 Normalized breakthrough time at 1.0 µg/cm²/min [mins] EN Classification according to EN 14325 SSPR Steady state permeation rate [µg/cm²/min] MDPR Minimum detectable permeation rate [µg/cm²/min] CUM 480 Cumulative permeation mass after 480 mins [µg/cm²] Time 150 Time to reach cumulative permeation mass of 150 µg/cm² [mins] ISO Classification according to ISO 16602 CAS Chemical abstracts service registry number...

Open the catalog to page 6
DuPont™ Tyvek® IsoClean® , Model IC 183 B WH DS - 7

Permeation Data for Tyvek® IsoClean® CS Hazard Name Physical State BT Act (Actual) Breakthrough time at MDPR [mins] BT 0.1 Normalized breakthrough time at 0.1 µg/cm²/min [mins] BT 1.0 Normalized breakthrough time at 1.0 µg/cm²/min [mins] EN Classification according to EN 14325 SSPR Steady state permeation rate [µg/cm²/min] MDPR Minimum detectable permeation rate [µg/cm²/min] CUM 480 Cumulative permeation mass after 480 mins [µg/cm²] Time 150 Time to reach cumulative permeation mass of 150 µg/cm² [mins] ISO Classification according to ISO 16602 CAS Chemical abstracts service registry number...

Open the catalog to page 7
DuPont™ Tyvek® IsoClean® , Model IC 183 B WH DS - 8

Important Note The permeation data published have been generated for DuPont by independent accredited testing laboratories according to the test method applicable at that time (EN369, ASTM F739, EN 374-3, EN ISO 6529 (method A and B) or ASTM D6978) The data is typically the average of three fabrics samples tested. All chemicals have been tested at an assay of greater than 95 (w/w) % unless otherwise stated. The tests were performed at room temperature and environmental pressure unless otherwise stated. A different temperature may have significant influence on the breakthrough time....

Open the catalog to page 8

All DuPont Personal Protection catalogs and technical brochures

Archived catalogs