CRANE SET
28Pages

BRIDGE CRANE COMPONENTS TO CREATE YOUR CUSTOM BRIDGE CRANE A series of products conceived and designed to be assembled and create a bridge crane suited to your needs Power driven travel heads with DGT/DGP series wheel units DGT series wheel units with DGP series suspended gear motor DRH series wire rope hoists (in the figure) - DMK series chain hoists Electrical control panel Bridge beams (NOT SUPPLIED) but dimensioned with ARIANNA software

SUSPENDED BRIDGES: DPS SERIES KIT 6 DRH series wire rope hoists - DMK series chain hoists (in the figure) Electrical control panel ower driven travel heads with DMT 3-4-5 series trolleys P Bridge beams in I Iron NOT SUPPLIED but indicated in the technical tables Selected software for standard components for standing/suspended bridge cranes

Donati products are designed and built taking into consideration the "Essential Safety Requirements" of annex I to the Machinery Directive 2006/42/EC and are issued on the market equipped with an EC IIA declaration of conformity or IIB declaration of incorporation based on the type of component. They are also in compliance with the following directives: ■ LOW VOLTAGE DIRECTIVE 2014/35/UE ■ ELECTROMAGNETIC COMPATIBILITY DIRECTIVE 2014/30/UE PROTECTION AND SHEATHING OF ELECTRICAL PARTS ■ Sliding motors: protection IP55 (motor) - IP23 (brake); class "F" insulation ■ Limit switch: minimum...

TRAVEL HEADS FOR STANDING BRIDGE CRANE The main components on end-carriages for bridge cranes are the: END-CARRIAGE FRAMEWORK: T he load-bearing structure is made from rectangular tubular. T he bridge crane girders are fixed to the end-carriage structure using a system of high-resistance bolts and a pin centring system. END-CARRIAGE FOR SINGLE GIRDER BRIDGE CRANE travelling drive unit comprising “DGT” wheel group and “DGP” offset geared-motor group joining cross plates between the beam and bridge crane girder idle drive unit comprising “DGT” wheel group body framework in tubular...

DONATI end-carriages are designed for handling operations on bridge crane rails: ■ at single running speed from 3.2 to 25 m/min; ■ at two running speeds, from 12.5/3.2 to 80/20 m/min; operating on: ■ single girder, with a capacity of up to 20,000 kg and gauge of up to 25 m; ■ double girder, with a capacity of up to 40,000 kg and gauge of up to 27 m. Designed and built on the principle of modular components assembled together in relation to their specific use, they are equipped with drive units comprising "DGT" series wheel groups, which are combined with "DGP" series offset geared motors....

OPERATING LIMITATIONS FOR END-CARRIAGES ON SINGLE GIRDER BRIDGE CRANES BASED ON: CAPACITY - ISO/FEM GROUP - SPAN CAPACITY ISO/FEM (kg) GROUP Admissible travelling mass for end-carriages on SINGLE GIRDER bridge crane [ Travelling mass (kg) = capacity + crane weight + weight of trolley/hoist ] Note: operating limitations determined using Donati components (hoist, trolley, etc.) and sectioned beams sized as per arrow a = Span / 750 TRAVEL HEADS FOR STANDING BRIDGE CRANE OPERATING LIMITATIONS FOR END-CARRIAGES ON DOUBLE GIRDER BRIDGE CRANES BASED ON: CAPACITY - ISO/FEM GROUP - SPAN Admissible...

TRAVEL HEADS FOR STANDING BRIDGE CRANE “DGT” SERIES WHEEL GROUPS D rive wheels Ø 125, Ø 160, Ø 200, Ø 250 and Ø 315 are carbon steel moulded. Sliding wheels Ø 400 and Ø 400 R are in spheroid cast iron. A ll wheels groups revolve on permanently lubricated radial bearings, with the exception of the extra load capacity Ø 400 R wheel group, which is fitted with roller bearings. A vailable in idle operation or ready for drive operation combined with an offset geared-motor. I n drive operation, the direct connection is coaxial between the offset geared-motor output shaft and the grooved hub on...

WHEEL SPECIFICATIONS WHEEL GROUP CLEARANCE (mm) INTERNAL WIDTH Quotes L2 in red refer to wheels operating with For 0 315 and 0 400 wheels with a “special” a “standard” and “maximum” sheave: sheave, the quota L2 increases by 10 mm, with respect to the values listed in the table TRAVEL HEADS FOR STANDING BRIDGE CRANE

DPS SINGLE GIRDER SUSPENSION BRIDGE KITS The KIT includes the supply of all the components necessary for assembly of a single girder suspension bridge crane. The bridge girder is not included in the KIT but the catalogue shows the recommended and tested IPE or HEA girders. The catalogue prescribes the use of HEA girders for heads and IPE or HEA girders for bridge girders. The trolleys and head can have different combinations based on the capacity and the width of the flange of the rail; in general there is a drive trolley and an idle trolley for each head. For Kits with a capacity up to...

SUSPENSION BRIDGE DPS1 - CAPACITY 1000 KG - HOIST DMK Sc pr HEAD (DIMENSIONS IN mm) BRIDGE (DIMENSIONS IN mm) HEA GIRDER Weight CODE GIRDER TYPE Ht Lt L D 0R O O1 O2 Q Q1 kg HEAD PAIR TYPE Hp Lp U For VdC with flange greater than 220 mm, increase the dimension D and U by 60 mm with Head 1200, 42 mm with Head 1500 and 23 mm with Head 1800 SUSPENSION BRIDGE DPS2 - CAPACITY 2000 KG - HOIST DMK HEAD (DIMENSIONS IN mm) BRIDGE (DIMENSIONS IN mm) Pr HEA GIRDER Weight CODE GIRDER TYPE Ht Lt L D 0R O O1 O2 Q Q1 kg HEAD PAIR TYPE Hp Lp U For VdC with flange greater than 220 mm, increase the dimension...

SUSPENSION BRIDGE DPS3 - CAPACITY 3200 KG - HOIST DMK CODE HEAD PAIR BRIDGE (DIMENSIONS IN mm) GIRDER SUSPENSION BRIDGE DPS4 - CAPACITY 4000 KG - HOIST DMK CODE HEAD PAIR

SUSPENSION BRIDGE DPS1 - CAPACITY 1000 KG - HOIST DRH1 Sc HEAD (DIMENSIONS IN mm) Pr HEA GIRDER TYPE Ht Weight CODE HEAD PAIR BRIDGE (DIMENSIONS IN mm) GIRDER TYPE HP For VdC with flange greater than 220 mm, increase the dimension D and U by 60 mm with Head HEA100, 42 mm with Head HEA120 and 23 mm with Head HEA140 Sc Pr HEA GIRDER HEAD (DIMENSIONS IN mm) Weight CODE HEAD PAIR BRIDGE (DIMENSIONS IN mm) GIRDER TYPE HP LP T218J03 For VdC with flange greater than 220 mm, increase the dimension D and U by 37 mm with Head HEA120, and 18 mm with Head HEA140