2.4” IPS LCD Module with SPI Interface DT024ETFT-IPS, DT024ETFT-IPS-SHB Displaytech, a SEACOMP company Phone: 1.760.918.6722 [email protected] Contents of this document are subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or physical, for any purpose, without the express written permission of Displaytech.

2.1 MCU Serial Interface Mode 2 3.1 Absolute Maximum Ratings 3 7.6 Cautions for installation and assembly 12

The DT024ETFT-IPS and DT024ETFT-IPS-SHB are 2.4” color IPS LCD modules, each composed of a LCD panel, display drivers, FPC display cable with SPI interface, and adjustable LED backlight unit. The display’s active area has a resolution of 240 x 320 pixels. The DT024ETFT-IPS-SHB, with twice the number of backlight LEDs, is available as a “super high-bright” alternative to the DT024ETFT-IPS. • Video Systems • Mobile Systems • Wearable devices • Module Dimensions • Active Area • Pixel Pitch • Viewing Direction • Backlight Type IPS, Normally Black, Transmissive Flexible Printed Circuit Liquid Crystal...

1 Recommended mating connector: 5051101592 (or equivalent)

Operation outside of the maximum ratings listed below may result in permanent damage to the LCD.

5 DT024ETFT-IPS backlight power consumption: 594mW (Max.) 6 DT024ETFT-IPS-SHB backlight power consumption: 1.19W (Max.) 7 LED lifetime is defined as the amount of time it takes for brightness to decrease to 50% of its original value at TA=25°C and IF=40mA. LED lifetime may decrease if operating current, IF, is larger than 40mA.

4.1 3-Line Serial Interface Figure 3: 3-Line Serial Interface Timing

Figure 4: 4-Line Serial Interface Timing

1 Refer to ILI9341 driver datasheet for details

5.1 Figures Figure 3: Optical Measurement System Conditions: IF = 40 mA, TA = 25 °C, ambient brightness < 150 lx Figure 4: Response Times Decay Time (TF) = Time required for display to transition from white to black Rise Time (TR) = Time required for display to transition from black to white Figure 5: Viewing Angles Viewing angle is measured from center point of LCD

Chromaticity = Area of △RGB / Area of △NTSC * Color coordinates measured at center point of LCD Figure 7: Luminance Uniformity Luminance is defined as the brightness of all white pixels at the center of the display area at optimum contrast. Uniformity is determined by measuring Luminance at 9 points and calculating LuminanceMIN / LuminanceMAX Contrast Ratio = Surface LuminanceWhitePixels Surface LuminanceBlackPixels

Judgment is based on inspection performed after testing, per criteria described in the Inspection Criteria table.18 18 Functional test shall be conducted after 4 hours of storage at normal temperature and humidity, after LCD is removed from test chamber.

Liquid crystal in LCD is poisonous. Do not put in mouth. If liquid crystal comes in contact with skin or clothes, wash it off immediately using soap and water. A. The LCD panel is made of plate glass. Do not subject the panel to mechanical shock or excessive force on its surface. B. In order to ensure reliability, do not hold product by flexible printed circuit (FPC) cable. C. Provide space so that panel does not come into contact with other components. D. To protect the product from external force, apply a covering lens (acrylic board or similar) and keep an appropriate gap between them. E....

PULL TAPE(YELLOW) Graphite sheet DISPLAY INTERFACE Viewing Direction:ALL White label Tuffy Glue temperature tape COMPONENTS AREA Contact Side Notes PIXEL DETAIL Count drawing & Spec.revision record during discussion with customer Revision content description Modify Dimension Modify backlight led circuit. SIZE DESIGNER FILE NAME lO.Environmental Protections Requirements(s): RoHS 11. (^Reference Dimension; i i=Critical/lnspection Dimension Jones Hsieh Count Dwg