Website: www.displaytech.com.hk Product: 64128P Series (128 x 64 Dots) Contents in this document are subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Displaytech Ltd.

1. REVISION RECORD VERSION

NOTE 2: THERSHOLD VOLTAGE AND SATURATION VOLTAGE Vth: The voltage Vop which the transmission rate of segment is 90%(positive) or 10%(negative) of saturated value on conditions of the selected waveform.(non-selected waveform is opposition) Vsat: The voltage Vop which the transmission rate of segment is 10%(positive) or 10%(negative) of saturated value on conditions of the selected waveform.(non-selected waveform is opposition)

l.Driving waveform: static waveform. 2.Voltage applied to all segments NOTE 5: CONTRAST RATIO (CR) 5.1 POSITIVE TYPE: Measuring Methode Of Capacitance Voltage applied to all segments.

8. BACKLIGHT DRAWING 8.1. Lightbox Type Backlight (Yellow Green in color)

9. BACKLIGHT SPECIFICATION 9.1. LIGHTBOX TYPE BACKLIGHT (YELLOW GREEN IN COLOR) CIRCUIT DIAGRAM: TESTING POINT CIRCUIT DIAGRAM 1. AVERAGE LUMINOUS INTENSITY IS THE AVERAGE VALUE OF THE NINE INDICATED POINTS AS SHOWN. 2. MEASUREMENT INSTRUMENT: BM-7, APERTURE: ’ 10mm.

9.2. LOW POWER TYPE BACKLIGHT (RED / WHITE / BLUE / PURE GREEN / AMBER IN COLOR) 9.2.1. Mechanical Specifications TESTING POINT CIRCUIT DIAGRAM 1. AVERAGE LUMINOUS INTENSITY IS THE AVERAGE VALUE OF THE NINE INDICATED POINTS AS SHOWN. 2. MEASUREMENT INSTRUMENT: BM-7, APERTURE: ' 10mm.

10.QUALITY GUARANTEE 10.1. PURPOSE: It is to define the inspection standard of LCD modules • FUNCTION TEST • APPEARANCE INSPECTION • PACKING SPECIFICTION • Put under the lamp (20w*2) at a distance 100mm from the LCD Modules. • Tilt upright 45 degree by the front (back) to inspect LCD appearance. • SAMPLING METHOD • SAMPLING PLAN • MAJOR DEFECT • MINOR DEFECT • GENERAL LEVEL 0.65% (MAJOR) 2.5% (MINOR) II/NORMAL

1) FUNCTIONAL TEST STANDARD Inspection Standard Description Defect type Display wrong pattern Display segment open Dimsegment I Dimsegment Reject Wrong LCD viewing direction Pattern parallelism

2) COSMETIC INSPECTION STANDARD

Standard description of inspection Standard Defect type Black line in L cd Line defect Finger print PCB/COB specification PCB deformity Deformity at PCB edge, damage circuit. Damage excess 2x2mm at the PCB corner Scratch on PCB coat/leakage coat on PCB surface Open circuit Color different from one side to another side. Repaired solder mask area Scratch circuit, damage Circuit Bezel specification

Standard description of inspection h≦0.01 mm/mm h>0.01 mm/mm Standard Defect type Accept Reject MIN 3.10 Void gap between bezel and PCB Bezel clip incorrectly 4 Solder specification 4.1 Wrong component 4.2 Broken component Reject Reject Component legs extend beyond the pad and Legs >pad distance(w) on solder area >W2 Component legs extend beyond the pad and Legs >pad distance(w) on solder area 1/4W 4.5 CHIP components hoist≦0.5mm 4.6 CHIP components hoist>0.5mm Accept Reject

Displaytech Ltd LCD MODULE 64128P SERIES Version : 1.0 1. This device is susceptible to Electro-Static Discharge (ESD) damage. Observe Anti-Static precautions. 2. The display panel is made of glass. Do not subject it to a mechanical shock by dropping it or impact. 3. If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water. 4. Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 5. The polarizer...

11.5. Storage Precautions When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. Keep the modules in bags (avoid high temperature / high humidity and low temperatures below 0°C). Whenever possible, the LCD modules should be stored in the same conditions in which they were shipped from our company. 11.6. Others Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low temperature....

LCD MODULE 64128P SERIES Version : 1.0 module or making any alterations or modifications to it. 1. Do not alter, modify or change the shape of the tab on the metal frame. 2. Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached. 3. Do not damage or modify the pattern writing on the printed circuit board. 4. Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector. 5. Except for soldering the interface, do not make any alterations or modifications with a soldering iron. 6. Do not drop, bend...

LCD MODULE 64128P SERIES Version : 1.0 12.7. Storage When storing LCDs as spares for some years, the following precaution are necessary. 1. Store them in a sealed polyethylene bag. If properly sealed, there is no need for desiccant. 2. Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature between 0°C and 35°C. 3. The polarizer surface should not come in contact with any other objects. (We advise you to store them in the container in which they were shipped.) • Do not leave them for more than 168hrs. at 60°C. • Should not be left for more than 48hrs....