![DIGISOUND-Electronic - logo](https://img.directindustry.com/images_di/logo-p/L16167.gif)
Catalog excerpts
![F/DHW 1 - 1](https://img.directindustry.com/pdf/repository_di/16167/f-dhw-1-558387_1m.jpg)
Dynamic Telephone Receiver Dynamische Telefon-Hörkapsel Technical terms Technische Daten DC Resistance Gleichstromwiderstand Impedance Impedanz Rated input power Nenn-Eingangsleistung Maximum input power maximale Eingangsleistung Sensitivity Empfindlichkeit Construction for sensitivity evaluation Aufbau zur Empfindlichkeitsermittlung: Temperature range Temperaturbereich Weight Gewicht (nominal) Solderability Lötbarkeit: Suitable for hand soldering according geeignet für Handlötung gemäß Resistance against solder heat Lötwärmebeständigkeit: No deterioration after dipping the terminals in solder of 260 ± 5 ° for 10 s. C Keine Verschlechterung nach Eintauchen der Terminals in Lot von für Buzz&Rattle test: sine wave of following voltage (RMS) Kein Surren/Rasseln bei Anlegen folgender Sinusspannung (effektiv) All electrical and acoustical characteristics must be kept after following test procedures (SPL: allowable deviation after testing ± 2 dB of the initial value): Alle elektrischen und akustischen Kennwerte müssen nach folgenden Test-Prozeduren eingehalten werden (Schalldruckpegel: zulässige Abweichung nach dem Testen ± 2 dB vom Ausgangswert): Halbzeug, Werkstoff Untolerierte Maße Maßstab Vervielfält.-Pause Nr. gezeichnet Arbeitspause Nr. bearbeitet geprüft normgepr.
Open the catalog to page 1![F/DHW 1 - 2](https://img.directindustry.com/pdf/repository_di/16167/f-dhw-1-558387_2m.jpg)
Reliability Zuverlässigkeit: High temperature storage test Hochtemperatur-Lagerungs-Test: +70 ± 2 ° 72 h C, High temperature humidity storage test +40 ± 2 ° 92 ± 2 % R.H. rel. LF, 96 h C, Hochtemperatur-Feuchte-Lagerungs-Test Low temperature storage test Tieftemperatur-Lagerungs-Test: -20 ± 2 ° 72 h C, Temperature cycling test: 5 cycles; 1 cycle consisting of -20 ± 2 ° 30 min, C, Temperatur-Zyklus-Test: 5 Zyklen; 1 Zyklus bestehend aus +20 ± 5 ° 15 min, C, +70 ± 2 ° 30 min, C, and und +20 ± 5 ° 15 min. C, Drop test Fall-Test: Receiver unit must withstand 3 times falling (in three mutually...
Open the catalog to page 2![F/DHW 1 - 3](https://img.directindustry.com/pdf/repository_di/16167/f-dhw-1-558387_3m.jpg)
Tolerance frame Toleranzfenster: (For attention: This is a relative tolerance frame, i. e. movable in vertical direction. Usually, the measuring equipment „HEAD-ACOUSTIC CAS-2.5" - used by customer - will automatically place the curve closest to the upper limit.) Zur Beachtung: Dieser Toleranzrahmen is relativ, d. h. in vertikaler Richtung verschieb- bar. Im Regelfall wird das Metisystem „HEAD-ACOUSTIC CAS-2.5" - welches vom Kunden verwendet wird - die Kurve automatisch an das obere Limit legen.) No sharp peaks respectively dips nor abrupt steps allowed in frequency response curve....
Open the catalog to page 3![F/DHW 1 - 4](https://img.directindustry.com/pdf/repository_di/16167/f-dhw-1-558387_4m.jpg)
Leakage sensitivity Leckempfindlichkeit: To be evaluated with a standarized leakage-ring which for measurement replaces frontpiece of IEC318-coupler. Zu ermitteln mittels standardisiertem Leckring, welcher bei der Messung das Frontstück des IEC318-Kopplers ersetzt. ∆ RLRLeakage = < 2.6 dB Hearing aid compatibility Hörhilfen-Kompatibilität: (important for use in some specific markets/countries) acc. nach standard ETS 300 381 (wichtig für den Gebrauch in einigen speziellen Märkten/Ländern) Remark Anmerkung: Due to customers measurements according to ETS 300 381 in the handset the dynamic...
Open the catalog to page 4![F/DHW 1 - 5](https://img.directindustry.com/pdf/repository_di/16167/f-dhw-1-558387_5m.jpg)
Dimensions Abmessungen: Each soldering tag with one hole dia. 1.0 mm Jede Lotfahne mit einem Loch 0 1.0 mm Soldertag's surface is tinned galvanically (electroplated); plating thickness: >= 5 |am tin-layer Lotfahnen-Oberflache galvanisch verzinnt; Mindest-Schichtdicke: >= 5 /urn Zinnschicht Halbzeug, Werkstoff Untolerierte MaBe
Open the catalog to page 5![F/DHW 1 - 6](https://img.directindustry.com/pdf/repository_di/16167/f-dhw-1-558387_6m.jpg)
APPENDIX ANHANG: Circuit diagram „Interface grey“ Schaltbild „Schnittstelle grau“: Halbzeug, Werkstoff Untolerierte Maße Maßstab Vervielfält.-Pause Nr. gezeichnet Arbeitspause Nr. bearbeitet geprüft normgepr.
Open the catalog to page 6All DIGISOUND-Electronic catalogs and technical brochures
-
F-B-M7505IPB
4 Pages
-
MEMS Microphone Portfolio
2 Pages
-
F-B-M0403ESB
6 Pages
-
F/HU 110P12V IP67B
2 Pages
-
F-B-P2612IPB-01
4 Pages
-
Catalogue Vibration Motors
3 Pages
-
Explosion-Proof Products
8 Pages
-
SIREN Portfolio
4 Pages
Archived catalogs
-
Ceramic Vacuum Relays
16 Pages
-
F/HU110P12V-IP67B
2 Pages
-
F-B-P3012EGPB
3 Pages