® SPECIFICATION DC SUPPLY 8 V to 35 V continuous CRANKING DROPOUTS Able to survive 0V for 50mS, providing the supply was at least 10V before dropout and supply recovers to 5V START RELAY OUTPUT 16A DC supply at supply voltage FUEL RELAY OUTPUT 16A DC at supply voltage AUXILIARY RELAY OUTPUTS 5A DC at supply voltage CHARGE FAIL/EXCITATION RANGE 0V to 35V MAXIMUMOPERATING CURRENT 320mA at 12V, 215mA at 24V MAXIMUMSTANDBY CURRENT 175mA at 12V, 95mA at 24V ALTERNATOR INPUT RANGE 15V (L-N) to 333V AC (L-N) absolute maximum ALTERNATOR INPUT FREQUENCY 50-60 Hz at rated engine speed (Minimum: 15V AC L-N) MAGNETICPICK-UP VOLTAGE INPUTRANGE +/- 0.5V to 70V Peak MAGNETIC INPUT FREQUENCY 10,000 Hz (max) at rated engine speed MAINS (UTILITY) SENSING INPUT RANGE (DSE5220 only) 15V (L-N) to 333V AC (L-N) absolute maximum MAINS(UTILITY)SENSINGINPUTFREQUENCY (DSE5220 only) 50-60 Hz MAINS (UTILITY) & GENERATOR LOADING RELAY OUTPUT (DSE5220 only) 8A AC 250V MODULE DIMENSIONS (WxH) 240mm x 172mm 9.4” x 6.8” PANEL CUT-OUT (WxH) 220mm x 160mm 8.7“ x 6.3” MAXIMUMPANEL THICKNESS 8mm 0.3” The DSE5210 is an Automatic Start ControlModule designed to automatically start and stop diesel and gas generating sets that include non electronic engines. The module also provides excellent engine monitoring and protection features. The module has the ability to monitor under speed, over speed, charge failure, emergency stop, low oil pressure, high engine temperature, fail to start, fail to stop, under/over generator volts, over current, under/over generator frequency, low/high DC battery volts, low fuel alarm and loss of the speed sensing signal. The module displays fault conditions on the LCD display and via the LED indicators on the front. The DSE5220 is an Automatic Mains Failure ControlModule and includes all the features of the DSE5210 plus the ability tomonitor a mains (utility) supply. Upon detection of a mains (utility) failure the module automatically starts the generating set. Once the mains (utility) power has been restored it instructs the generating set to stop. Both modules include RS232 or RS485 communications capabilities for linking to a PC, sending SMS messages and interfacing with new and existing buildingmanagement systems. FEATURES • Automatic start • Automatic mains (utility) failure detection (DSE5220 only) • Automatic load transfer • Configurable inputs • Configurable outputs • Configurable alarms & timers • Digital inputs • Analogue inputs • Back-lit character LCD display • Engine protection • Front panel mounting • PC configurable • Front panel programming • Remote monitoring • RS232 or RS485 remote communications (to be specified on ordering) • Modbus RTU • Engine history event log • LED alarm indication • LCD alarm indication • SMS messaging • Hid till lit alarm icons • Engine exercise mode • Magnetic pick-up BENEFITS • Full integration into new and existing building management systems • In-built engine diagnostics removes the requirement for service equipment • License free PC software • Modules help to improve the life cycle of engine starter motors • On-site module configuration to match user requirements • Remote module configuration using PC software • Modules send SMS messages to engineers to notify specific engine problems (GSM Modem and SIM Card required) • User-friendly set-up and button layout OPERATION The modules are operated using the front STOP, AUTO and MANUAL push buttons. The DSE5220 also includes a TEST button. An additional push button allows the user to scroll through the LCD display to view the instrumentation and event log. CONFIGURATION The modules can be configured using the front panel buttons or by using the DSE810 interface and PC software. DSECONTROL® MONITORING WITH INTELLIGENCE. DSE5210 & DSE5220 AUTO START & AUTOMAINS FAILURE CONTROLMODULES DSE5210 DSE5220

LED INDICATION Hid till lit icons are used to show the presence of alarm conditions detected by the modules. The icons appear to the left of the LCD display. TELEMETRY The module gives the user full telemetry facilities when using the optional communications software. The module can be connected to a PC using the DSE810 PC interface or by using a suitable modem. The PC software is Microsoft Windows™ based. All access into the module can be configured to be password protected to prevent unauthorised entry. The PC software allows the module to be controlled from a remote location. INPUTS & OUTPUTS...

® DSE5210 & DSE5220 2 AMP FUSES G M 2 AMP FUSES BATTERY -VE +VE FUEL EMERGENCY STOP LOW OIL PRESSURE HIGH COOLANT TEMP FUEL LEVEL SENDER USER CONFIGURABLE -VE INPUT 1 USER CONFIGURABLE -VE INPUT 2 USER CONFIGURABLE -VE INPUT 3 USER CONFIGURABLE -VE INPUT 4 USER CONFIGURABLE -VE INPUT 5 USER CONFIGURABLE -VE INPUT 6 USER CONFIGURABLE +VE INPUT USER CONFIGURABLE +VE INPUT USER CONFIGURABLE +VE INPUT UPTO 32 AMPS FUSE MIN 2 AMP MAX 20 AMP ANIT-SURGE FUSE BATTERY FUEL WL CRANK CHARGE ALT CRANK CHG ALT OIL WATER SENDER COMMON IMPUTS PLANT +VE MAINS LOADING RELAY GENERATOR LOADING RELAY OUTPUTS GEN...

® DEEP SEA ELECTRONICS INC 3230 Williams Avenue Rockford IL 61101-2668 USA TELEPHONE +1 (815) 316 8706 FACSIMILE +1 (815) 316 8708 EMAIL [email protected] WEBSITE www.deepseausa.com DEEP SEA ELECTRONICS PLC Highfield House Hunmanby Industrial Estate Hunmanby, North Yorkshire YO14 0PH England TELEPHONE +44 (0)1723 890099 FACSIMILE +44 (0)1723 893303 EMAIL [email protected] WEBSITE www.deepseaplc.com Registered in England & Wales No.01319649 VAT No.316923457 YOUR LOCAL DISTRIBUTOR. DEEP SEA ELECTRONICS PLC maintains a policy of continuous development and reserves the right to change the details...