Catalog excerpts
Screwdriving Technology Automation Air Motors Air Tools machines unlimited Torque Transducers Transducers, measurement platforms and measurement wrenches nn highly accurate measurements nn wide measurement range nn in-process control with the torque transducer The selection of a suitable torque transdu-cer is a basic requirement for the adjust-ment, monitoring and inspection of screw-drivers, and also for the testing of screw joints and screw joint analysis. Measuring Technology
Open the catalog to page 1Examples for the use of the most suitable measurement device for processing reliability requirements Example 1: An operator always assembles the same type of screw using a DEPRAG pneumatic screwdriver. Through the driver shut-off when the preset torque is reached, the assembly is controlled and assured to be accurate. In certain intervals, the screwdrivers are cross-checked using torquetransducers and if deviations occur, readjustments can be made. Measurement platforms which are intended for stationary use in a measurement laboratory or on a mobile measurement station are suitable for this...
Open the catalog to page 2TECHNICAL DATA Transducer (DMS, non-contact signal transmission) Type Part no. Calibrated measuring range Permissible overload Speed max. Weight approx. Required Accessories Measuring Instrument Connector Cable (for transducer to measuring instrument ME 5…) Length 2 m / 4 m / 6 m Part no. 6.6’ / 13’ / 20’ Power Supply for transducer Part no. connected to measuring instrument ME 5000 Power Supply Cable 220 V / 110 V Part no. When connected to a DEPRAG measuring instrument, this transducer is ideal for torque acquisition and documentation of all acquired results of screw joints and assembly...
Open the catalog to page 3TECHNICAL DATA Piezoelectric (PE) transducers: measuring platforms Calibrated measuring range *) Permissible overload Typical measurement uncertainty Sensibility Frequency response Linearity Diameter D Weight Connecting plug Type Part no. Nm in.lbs % % pC / Ncm kHz ≤ % mm / in. kg / lbs type Strain gage (DMS) transducers: measuring platforms Type Part no. Nm Calibrated measuring range *) in.lbs Permissible overload % Typical measurement uncertainty % Sensibility at nominal torque mV/V Operational temperature range °C °F Parameter temperature coefficient % / K Zero signal temperature...
Open the catalog to page 4TECHNICAL DATA Piezoelectric (PE) transducer: E-torque wrench Calibrated measuring range *) Permissible overload Typical measurement uncertainty Sensibility Frequency response Linearity Length L Weight Connecting plug Type Part no. Nm in.lbs % % pC / Ncm kHz ≤% mm / in. kg / lbs type Strain gage (DMS) transducers: E-torque wrench Calibrated measuring range *) Permissible overload Typical measurement uncertainty Sensibility at nominal torque Operational temperature range Parameter temperature coefficient Zero signal temperature coefficient Supply voltage (DC) Length L Weight Connecting plug...
Open the catalog to page 5accessories Required Accessories For Piezoelectric (PE) transducers: measuring platforms For Piezoelectric (PE) transducer: E-torque wrench Connection cable to measuring instrument 5 m/16.4 ft. Connection cable to measuring instrument 1 m/3.3 ft. Type MP1PE Type Part no. 810675 Part no. For Strain gage (DMS) transducers: measuring platforms For Strain gage (DMS) transducers: E-torque wrenches, angle head design For Strain gage (DMS) transducers: E-torque wrenches, straight design Connection cable to measuring instrument 2 m/ 6.6 ft. Connection cable to measuring instrument 4 m/13.2 ft....
Open the catalog to page 6Calibration of DEPRAG measurement transducer or factory calibration of a measurement device or measurement electronic - for special order DAkkS-calibration in accordance with DIN 51309 Strain gauge measurement transducer Load right/left 3 mounting positions 8 measurement points DAkkS-calibration certificate Part no. 3855281 Factory calibration in accordance with DIN 51309 Strain gauge or piezo measurement transducer Load right/left 3 mounting positions 8 measurement points Factory calibration certificate Part no. 3855282 Factory calibration in accordance with DIN 51309 Strain gauge or piezo...
Open the catalog to page 7Possible Combinations Possible Combinations Measuring principle: PIEZO-ELECTRIC Connection Cable: Measuring Instrument Torque Transducer Measuring type MP1PE, type MP25PE, Platforms: type MP200PE E-Torque-Wrenches: type MS25PE-W type MS25PE-WS Measuring principle: STRAIN GAGE Torque Transducer Connection Cable: Connection Measuring Instrument ME… to Measuring Platforms or Torque Wrenches Length 2 m Length 4 m Length 6 m Part no. 385493A Part no. 385493B Part no. 385493C Measuring Platforms: type MP2DMS type MP7DMS type MP25DMS type MP160DMS E-Torque Wrenches: type MS2DMS type MS7DMS type...
Open the catalog to page 8All DEPRAG SCHULZ GMBH u. CO. catalogs and technical brochures
-
Software Solutions & Updates
36 Pages
-
Step Feeder System D3835E
20 Pages
-
MINIMAT-EC
12 Pages
-
E-SFM
8 Pages
-
GET Turbine Generator
8 Pages
-
Air Motors
28 Pages
-
Feeding Technologies D3810
36 Pages
-
Services
12 Pages
-
Screwdriving System DEPRAG Plus
16 Pages
-
D6100
8 Pages
-
ADVANCED LINE
40 Pages
-
D 3550
2 Pages
-
Controller Technology
12 Pages
-
MICROMAT / MINIMAT Screwdrivers
24 Pages
-
Inserting Tools for Screwdrivers
20 Pages
-
MINIMAT Screwdrivers
4 Pages
-
D C A M
4 Pages
-
MINIMAT-E
8 Pages
-
D 6600
48 Pages
-
MINIMAT-T Depth Stop Driver
2 Pages
-
SENSOMAT
4 Pages
-
Screw Presenter
6 Pages
-
Storage Devices
4 Pages
-
BASIC LINE
8 Pages
-
Corporate Image
20 Pages
-
Measurement devices
4 Pages
-
Speed Regulator
2 Pages
-
Flat Head Wrenches
2 Pages
-
Screwdriver Function Module
12 Pages
-
Manual Work Stations
12 Pages
-
MINIMAT-EC-Servo Screwdriver
4 Pages
-
NANOMAT Control Screwdrivers
6 Pages
-
VARIOMAT
2 Pages
-
D 3460
4 Pages
-
D 3470
2 Pages
-
D 3520
2 Pages
-
D 3530
2 Pages
-
RECYCLING Drivers
2 Pages
-
Tape-on-reel Feeder
4 Pages
-
NANOMAT
2 Pages
-
Press-Insertion Systems
4 Pages
-
Flyer system integration
4 Pages