Catalogs >
DEPRAG SCHULZ GMBH u. CO. KG >
Torque Transducers

Torque Transducers
1 / 8Pages

Catalog excerpts

Measuring Technology Torque Transducers Transducers, measurement platforms and measurement wrenches n highly accurate measurements n wide measurement range n in-process control with the torque transducer The selection of a suitable torque transdu-cer is a basic requirement for the adjust-ment, monitoring and inspection of screw-drivers, and also for the testing of screw joints and screw joint analysis.

Open the catalog to page 1

EXAMPLES for the use of the most suitable measurement device for processing reliability requirements Example 1: An operator always assembles the same type of screw using a DEPRAG pneumatic screwdriver. Through the driver shut-off when the preset torque is reached, the assembly is controlled and assured to be accurate. In certain intervals, the screwdrivers are cross-checked using torquetransducers and if deviations occur, readjustments can be made. Measurement platforms which are intended for stationary use in a measurement laboratory or on a mobile measurement station are suitable for this...

Open the catalog to page 2

Technical Data – Transducer (DMS, non-contact signal transmission) Calibrated measuring range Permissible overload Speed max. Weight approx. Required Accessories Type ME5000, ME5500, ME5600, ME6000 or type ME6100 (see brochure D3022E ) Measuring Instrument Connector Cable (for transducer to measuring instrument ME 5…) Length 2 m / 4 m / 6 m Part no. 6.6’ / 13’ / 20’ Power Supply for transducer Part no. connected to measuring instrument ME 5000 Power Supply Cable 220 V / 110 V Part no. When connected to a DEPRAG measuring instrument, this transducer is ideal for torque acquisition and...

Open the catalog to page 3

Technical Data – Piezoelectric (PE) transducers: measuring platforms Type Part no. Nm Calibrated measuring range *) in.lbs Permissible overload % Typical measurement uncertainty % Sensibility pC / Ncm Frequency response kHz Linearity ≤ % Diameter D mm / in. Weight kg / lbs Connecting plug type Technical Data – Strain gage (DMS) transducers: measuring platforms Type Part no. Nm Calibrated measuring range *) in.lbs Permissible overload % Typical measurement uncertainty % Sensibility at nominal torque mV/V °C Operational temperature range °F Parameter temperature coefficient % / K Zero signal...

Open the catalog to page 4

Technical Data – Piezoelectric (PE) transducer: E-torque wrench Calibrated measuring range *) Permissible overload Typical measurement uncertainty Sensibility Frequency response Linearity Length L Weight Connecting plug Type Part no. Nm in.lbs % % pC / Ncm kHz ≤% mm / in. kg / lbs type Technical Data – Strain gage (DMS) transducers: E-torque wrench Calibrated measuring range *) Permissible overload Typical measurement uncertainty Sensibility at nominal torque Operational temperature range Parameter temperature coefficient Zero signal temperature coefficient Supply voltage (DC) Length L...

Open the catalog to page 5

Required Accessories For Piezoelectric (PE) transducers: measuring platforms For Piezoelectric (PE) transducer: E-torque wrench Connection cable to measuring instrument 5 m/16.4 ft. Connection cable to measuring instrument 1 m/3.3 ft. Type MP1PE Type Part no. 810675 Part no. For Strain gage (DMS) transducers: measuring platforms Type For Strain gage (DMS) transducers: E-torque wrenches, angle head design For Strain gage (DMS) transducers: E-torque wrenches, straight design Connection cable to measuring instrument 2 m/ 6.6 ft. Connection cable to measuring instrument 4 m/13.2 ft. Connection...

Open the catalog to page 6

Calibration of DEPRAG measurement transducer Factory calibration of a measurement device DAkkS-calibration in accordance with DIN 51309 Strain gauge measurement transducer Load right/left 3 mounting positions 8 measurement points DAkkS-calibration certificate Part no. 3855281 Factory calibration in accordance with DIN 51309 *) Strain gauge or piezo measurement transducer Load right/left 3 mounting positions 8 measurement points Factory calibration certificate Part no. 3855282 Factory calibration in accordance with DIN 51309 *) Strain gauge or piezo measurement transducer Load right 3...

Open the catalog to page 7

Possible Combinations Possible Combinations Measuring principle: PIEZO-ELECTRIC Connection Cable: Measuring Instrument Torque Transducer Measuring type MP1PE, type MP25PE, Platforms: type MP200PE E-Torque-Wrenches: type MS25PE-W type MS25PE-WS Measuring principle: STRAIN GAGE Torque Transducer Connection Cable: Connection Measuring Instrument ME… to Measuring Platforms or Torque Wrenches Length 2 m Length 4 m Length 6 m Part no. 385493A Part no. 385493B Part no. 385493C Measuring Platforms: type MP2DMS type MP7DMS type MP25DMS type MP160DMS E-Torque Wrenches: type MS2DMS type MS7DMS type...

Open the catalog to page 8