*mydirectindustry

MED 20x2_0

Product catalog summary

Electrical Specifications:
The solenoid operates at coil voltages of 6, 12, 24, and 115 VDC. It has a coil power of 12 Watts for continuous use, 30 Watts for intermittent use, and 120 Watts for pulse use. The coil is terminated with 24 AWG wire leads and is tape wrapped for insulation. It is rated for a Class B insulation with a maximum temperature of 130ºC (266ºF). The dielectric strength is 500 VRMS for voltages 30 volts and under, and 1000 VRMS plus twice the rated voltage for over 30 volts.

Mechanical Specifications:
The solenoid measures 2.000 inches in length and 1.25 inches in diameter. The plunger diameter is 0.438 inches and is guided by brass material. It is mounted using a 0.88 x 0.16 inch hex nut. The plunger weighs 1.91 oz, and the total weight is 8.96 oz. The life expectancy is 250,000 cycles, depending on load conditions. It has UL approval for insulation systems S130.

Features:
The solenoid is a two-position linear solenoid with tubular frame construction, designed for high performance in DC applications. Standard pull versions are available, and UL approval can be requested.

Force Curves:
The document provides force curves for different duty cycles: continuous, intermittent, and pulse. For continuous duty at 12 Watts, the cold force at 100% voltage with no gap is 186 oz, and the hot force is 158 oz. For intermittent duty at 30 Watts, the cold force is 220 oz, and the hot force is 187 oz. For pulse duty at 120 Watts, the cold force is 300 oz, and the hot force is 254 oz.

Standard Part Numbers:
The document lists part numbers with corresponding voltages, duty cycles, power, resistance, and typical force at various strokes. For example, part number 53806-80 operates at 6 VDC with continuous duty at 12 Watts, providing a force of 186 oz at 0.000 inches stroke.

Catalog excerpts

tubular frame solenoid Two position linear solenoid with tubular frame construction. Features • High performance construction • DC solenoids applications only • Standard pull versions available • UL approval available upon request ©2017 Deltrol Controls - A Division of Deltrol Corp. 2740 South 20th Street Milwaukee, WI 53215 USA | P: 414.671.6800 | F: 414.671.6809 | www.deltrol-controls.com | [email protected]

Open the catalog to page 1

MED 20x2.000 Force Curves DC - Continuous Duty - 12 Watts 200 180 160 140 Force Cold 100% Voltage 0 Gap 186 Oz. DC - Intermittent Duty - 30 Watts 250 Force Cold 100% Voltage 0 Gap 220 Oz. Force Hot 100% Voltage 0 Gap 187 Oz. DC - Pulse Duty - 120 Watts 350 Force Cold 100% Voltage 0 Gap 300 Oz. Standard intermittent duty cycle at nominal voltage is one (1) minute “ON” and three (3) minutes “OFF”. Standard pulse duty cycle is 100 milliseconds “ON” and 900 milliseconds “OFF”. Note: Cold Force @ 25°C (77°F) Coil Temperature Hot Force @ 130°C (266°F) Coil Temperature Approx. 36 sq. in. Heat Sink Required...

Open the catalog to page 2

MED 20x2.000Dimensional View Units: Inches [mm] LOCK WASHER HEX NUT .875” ACROSS FLATS X .16 THK. 3/4-16 UNF-2A THREAD PLUNGER STOP/BUFFER 2X 0.127± .003 [3.25 ± .08] unless otherwise specified INCHES ± .015 (MILLIMETERS 0.38) Standard Part Numbers Parts No. (*) Normally Stocked Non stocked items require a minimum order Specifications subject to change without notice 3 of 3 Rev 02/08/17 ©2017 Deltrol Controls - A Division of Deltrol Corp. 2740 South 20th Street Milwaukee, WI 53215 USA | P: 414.671.6800 | F: 414.671.6809 | www.deltrol-controls.com | [email protected]

Open the catalog to page 3

MED 20x2_0

MED 20x2_0

Catalog excerpts

All Deltrol Controls catalogs and technical brochures