*mydirectindustry

Catalogs
Deltrol Controls
D-70 D-Frame Solenoid

D-70 D-Frame Solenoid

Product catalog summary

Electrical Specifications
The D-Frame Solenoid offers coil voltages of 6, 12, 24, and 110 VDC. It supports continuous power at 13 Watts, intermittent power at 48 Watts, and pulse power at 130 Watts. The coil termination is via wire leads, and it supports continuous, intermittent, and pulse duty cycles. The coil is tape wrapped, with insulation class options of Class A (105ºC max) and Class B (130ºC max). Dielectric strength is rated at 500 VRMS for 30 volts and under, and 1000 VRMS plus 2X rated voltage for over 30 volts.

Mechanical Specifications
The solenoid measures 2.625” (L) x 1.562” (W) x 1.828” (H) and features a plunger diameter of 0.500”. The plunger guide is made of plastic, and it mounts using six #8-32 UNC-2B holes. The plunger weighs 1.92 oz., with a total weight of 19 oz. It has a life expectancy of 250,000 cycles, depending on load conditions.

Agency Approval
The solenoid has UL approval for continuous duty (File No. E57982) and insulation systems (File No. E74443).

Features
The solenoid is a two-position linear solenoid with D-frame construction, balancing cost and performance. Both AC and DC solenoids are available, with UL approval on many models.

Force Curves
The document provides force curves for continuous, intermittent, and pulse duty cycles. The standard intermittent duty cycle is 25% with a maximum of 3 minutes "ON" and 9 minutes "OFF". The standard pulse duty cycle is 10% with 100 milliseconds "ON" and 900 milliseconds "OFF". A heat sink of approximately 36 sq. in. is required.

Standard Part Numbers
The document lists part numbers with corresponding voltage, duty cycle, power, resistance, and typical force at various strokes. Continuous, intermittent, and pulse duty cycles are detailed with specific force values at different strokes.

Catalog excerpts

roc Deltrol CONTROLS D-FRAME SOLENOID Two position linear solenoid with D-frame construction. Features Balance of cost and performance Օ AC solenoids and DC solenoids available UL approval on many models Coil Voltages 6, 12, 24, 110 VDC Coil Power 13 Watts Continuous, 48 Watts Intermittent, 130 Watts Pulse Coil Termination Wire leads (standard) Duty Cycle Continuous, intermittent and pulse duty available (see standard part numbers on page 4) Coil Treatment Tape wrapped Insulation Class Class A Rating - 105°C (221°F) Max. (standard) Class B Rating - 130°C (266°F) Max. (optional) Dielectric Strength 30 Volts and Under: 500 VRMS Over 30 Volts: 1000 VRMS plus 2X rated voltage for 1 minute Mechanical Spթcifications Size 2.625" (L) x 1.562" (W) x 1.828" (H) (See page 2 for dimensional drawing) Forces See force curves on page 3 Plunger Diameter 0.500" Plunger Guide Material Plastic Mounting 6X #8-32 UNC-2B Mounting Holes Weight Plunger - 1.92 oz., Total - 19 oz. Life Expectancy 250,000 Cycles (Dependent on load conditions) Agency Approval UL File No. E57982 For Continuous Duty UL File No. E74443 For Insulation Systems S105, S130 All dimensions in Inches Specifications subject to change without notice 1 of 4 Rev 07/08/11 ©2011 Deltrol Controls - A Division of Deltrol Corp. 2740 South 20th Street Milwaukee, WI 53215 USA | P: 414.671.6800 | F: 414.671.6809 | www.deltrol-controls.com | [email protected]

Open the catalog to page 1

D-70 @ Deltrol Force Curves DC Continuous Duty - 13 Watts 0 .2 A .6 .3 1.0 stroke in inhes DC Intermittent Duty - 48 Watts 0 .2 .4 .6 .8 1.0 stroke in inches DC Pulse Duty - 130 Watts 1-1-1-ri-1-1痗r 9 -2 .4 .6 .B 1.0 Standard intermittent duty cycle at nominal voltage is 25%, with three (3) minutes maximum "ON" and nine (9) minutes minimum "OFF" in a repetitive cycle. Standard Pulse duty cycle is 10% with 100 milliseconds "ON" and 900 milliseconds "OFF". NOTE: Approx 36 sq. in. Heat Sink Required Specifications subject to change without notice 3 of 4 Rev 07/08/11 ©2011 Deltrol Controls - A Division...

Open the catalog to page 3

D-70 @ Deltrol Standard Part Numbers Parts No. Voltage Duty Cycle Power Resistance (Ohms) Operation Typical Force (oz). 100% Voltage, 77° F, Stroke @ 0.000" 0.125" 0.250" 0.500" 0.750" 50046-80 6 VDC Continuous 13 Watts 2.75 Pull 150 79 62 30 15 50046-81* 12 VDC 11 50046-83* 24 VDC 44.3 50046-93* 110VDC 940 50031-80 6 VDC Intermittent 48 Watts 0.75 Pull 211 130 112 82 50 50031-81* 12 VDC 3.0 50031-83* 24 VDC 12.0 50031-93* 110VDC 254 53714-81 12 VDC Pulse 130 Watts 1.1 Pull 247 180 165 135 100 53714-83 24 VDC 4.5 53714-93 110VDC 92 (*) Normally Stocked Non stocked items require a minimum order...

Open the catalog to page 4

D-70 D-Frame Solenoid

D-70 D-Frame Solenoid

Catalog excerpts

All Deltrol Controls catalogs and technical brochures