Catalog excerpts
NEW IDEAS IN MOTION CONTROL... This single-axis, Direct PWM amplifier is designed to fit into a standard 3U UMAC rack. It is intended for driving AC induction, permanent magnet brushless, linear, and brushed DC motors. It has a current rating of 15.0 A Continuous/30.0 A Peak. This drive will operate directly off of the power mains wired to the backplane, typically 110 VAC or 230 VAC, three phase or single phase with appropriate derating. An external power supply of +24 VDC @1A (regulated or unregulated) is required for logic power allowing the user to control motor power separately from control logic power. The amplifiers are interfaced to a PMAC controller via ACC-24E2, ACC-24E2M, ACC-24E3 (Power PMAC only), ACC-8F or ACC-8FS. These drive amplifiers are designed to receive logic-level direct digital PWM motor voltage command from the PMAC controller and convert them to high voltage for motor control. They provide the power conversion, motor current sense feedback to the PMAC controller, and comprehensive system protection. Each drive also accepts motor thermal overload sensors for drive shut down on motor over temperature. The host controller provides all other motor control functions. HARDWARE FEATURES Amplifier Output Current Ratings
Open the catalog to page 115.0 A Continuous/30.0 A Peak Output Power Ratings 3.585 kW (4.81 HP) Types Supported DC Brushless (Permanent Magnet Synchronous) AC Induction Hardware Features 1 amplifier channel Simple wiring High power density Extensive fault protection Locking motor connectors Closed loop hall effect current sensors Direct line connection with Soft Start Separate logic power and motor power 3U UMAC Rack format for small size and easy support Full isolation for PMAC and user interfaces Direct PWM control for best performance and cost Shunt Regulator (requires external Resistor) for Bus power...
Open the catalog to page 2CABKIT3C - Cable Kit for 3U Servo Drives CABPWM-1 - 600 mm (24 inches long) PWM Cable for 1-Axis CABPWM-2 - 900mm (36 inches long) PWM Cable for 1-Axis CABPWM-3 - 1.5 m (60 inches long) PWM Cable for 1-Axis CABPWM-4 - 1.8m (72 inches long) PWM Cable for 1-Axis CABPWM-5 - 2.1 m (84 inches long) PWM Cable for 1-Axis CABPWM-6 - 3.6 m (144 inches long) PWM Cable for 1-Axis GEO Drive Motor Power Cables - 14AWG Motor Power Cables Connector CONKIT3C - 3U Amplifier Connector Kit Regenerative GAR78 - 300W 78 OHM Regenerative Resistor with...
Open the catalog to page 3Geo 3U Servo Drive Amplifier - User Reference Manual 3U PWM - 3U Digital PWM Amplifier
Open the catalog to page 4All Delta Tau catalogs and technical brochures
-
Digital Counter/Tachometer H7CC
64 Pages
-
TURBO PMAC2 VME ULTRALITE
7 Pages
-
TURBO PMAC2 REALTIME EXPRESS
3 Pages
-
TURBO PMAC2 PCI
7 Pages
-
TURBO PMAC VME
6 Pages
-
POWER UMAC CPU 256 Axis
4 Pages
-
3U042
4 Pages
-
3U081
4 Pages
-
ACC-8D OPT4
3 Pages
-
ACC-8D OPT4A
3 Pages
-
ADVANTAGE 900 BASIC PACKAGE
3 Pages
-
PMAC MINI PCI 8 Axis
7 Pages
-
PMAC PCI 8 Axis
7 Pages
-
PMAC PCI LITE 8 Axis
7 Pages
-
PMAC VME 8 Axis
6 Pages
-
PMAC2A PC/104
6 Pages
-
POWER UMAC
4 Pages
-
TURBO UMAC
6 Pages
-
PMAC-NC PRO2 RUNTIME
3 Pages
-
Turbo Clipper Drive
2 Pages
-
Battery Issues with PMAC ISA
5 Pages
-
Digital IO accessories
2 Pages
-
MLDT Sensor
1 Pages
-
Slow communications
1 Pages