High Pres F/S 1 3/5/01 1:46 pm Page 6 SPRAY CHARACTERISTICS q Produces a uniform flat fan shaped pattern. q Requires minimal overlapping to produce an even distribution when used in multiple nozzle system. q High pressure body design with replaceable insert. q A wide range of flow rates and spray angles. q 0° nozzle sizes available on request. q 3 piece construction. Body, insert and retaining screw. q The orifice insert is manufactured in Tungsten Carbide for maximum wear resistance at higher pressures. q The insert is recessed for protection. q The high pressure body and retaining screw are manufactured in Stainless Steel as standard. q Standard thread is 1⁄4” Male BSPT. q Special bodies can be made to order. ORDER EXAMPLE 1⁄4” AQ 4-65°. HIGH PRESSURE TYPE AQ CONSTRUCTION AND MATERIALS DIMENSIONS AND WEIGHTS Thread Size A 1/4” Dimensions (mm) B C 24,5 15,3 13,0 Weight (g) 26 Maximum Recommended Pressure: 350 Bar.G. CAPACITY CHART Equiv. orifice size (mm) 35 50 AQ 0,5 0,45 0,68 0,81 0,94 1,14 1,36 1,66 1,92 2,15 AQ 0,6 0,51 0,75 0,89 1,06 1,26 1,51 1,84 2,13 2,38 AQ 0,7 0,53 0,90 1,07 1,25 1,52 1,78 2,18 2,51 2,81 AQ 0,8 0,61 1,14 1,36 1,59 1,92 2,27 2,78 3,21 3,59 AQ 1,0 0,66 1,32 1,57 1,89 2,23 2,63 3,22 3,71 4,15 AQ 1,25 0,74 1,70 2,03 2,38 2,87 3,39 4,15 4,79 5,36 AQ 1,5 0,79 2,00 2,39 2,83 3,38 3,97 4,86 5,61 6,27 AQ 2,0 0,91 2,68 3,20 3,78 4,53 5,29 6,47 7,48 8,36 AQ 2,5 1,04 3,33 3,98 4,54 5,62 6,62 8,10 9,36 10,4 AQ 3,0 1,09 4,16 4,97 5,67 7,03 7,94 9,72 11,2 12,5 AQ 3,5 1,22 4,54 5,42 6,44 7,67 9,46 11,5 13,3 14,9 AQ 4,0 1,32 5,30 6,33 7,57 8,95 10,5 12,8 14,8 16,6 AQ 6,0 1,57 7,95 9,50 11,3 13,4 15,8 19,3 22,3 24,9 AQ 8,0 1,83 10,6 12,6 15,1 17,9 21,1 25,8 36,4 33,3 AQ 11,5 2,16 15,5 18,5 21,6 26,2 30,6 37,4 43,2 48,3 NOZZLE NUMBER Contact our Helpline for any special requirements: Tel: +44 (0) 151 424 6821 Fax: +44 (0) 151 495 1043 e-mail:[email protected] Web:www.delavan.co.uk A.26 FLOW RATE IN LITRES/MIN AT Bar.G. 70 100 140 210 280 350 SPRAY ANGLES (°) @ 70 Bar.G. 25 40 50 65 80 95