- Catalogs
- DEFONTAINE - ROLLIX
- L-shaped profile slewing rings with internal gear
L-shaped profile slewing rings with internal gear
L-shaped profile slewing rings with internal gear
1. Product Identification and Proprietary Notice
The DUO-ROL-X crown gear is a patented and proprietary component owned by ROLLIX-DEFONTAINE. The document emphasizes strict confidentiality and prohibits unauthorized reproduction or communication of the plans without written consent. Notices are provided in French, English, and German to reinforce proprietary rights.
2. General Specifications
Each gear is uniquely identified by a reference number and includes historical revision data. Key specifications cover:
- Module and number of teeth
- Pressure angle, typically 20°
- Truncature (tooth tip shortening)
- Pitch diameter and profile shift (addendum modification)
- Dimensional data such as mean diameter, external diameter, and mounting hole sizes (e.g., M12, M8x1.00)
- Estimated weight in kilograms and pounds
- Run-out tolerances on pitch diameter and general dimensional tolerances following IT-ETR-061 and ISO 8015 standards
3. Mechanical and Assembly Details
The document specifies precise locations and sizes for mounting holes and grease holes, essential for secure installation and lubrication. It also identifies positions for filler plugs and hardening connection points on the raceway. Assembly instructions reference cage types (e.g., JPS) and note changes in gear width and external dimensions over revisions. Teeth orientation is predominantly right-handed with consistent pressure angles.
4. Manufacturing and Heat Treatment
Components are marked to distinguish hardened (trempée/gehartet) from non-hardened (non trempée/ungehartet) areas, critical for wear resistance and durability. Approximate locations for hardening connections and filler plugs are documented to guide manufacturing and quality control.
5. Tolerances and Quality Standards
Dimensional and run-out tolerances comply with IT-ETR-061 and ISO 8015 standards, ensuring precision and interchangeability. Measurements on teeth and pitch diameter run-out are controlled to maintain gear performance.
6. Historical and Revision Data
The document records historical part numbers, modifications in tooth width, external dimensions, and assembly methods. Dates for design, verification, and sampling are included to track development and quality assurance.
Critical Information and Best Practices
- Strict adherence to confidentiality and proprietary rights is mandatory.
- Assembly must follow specified implantation references and cage types to ensure correct function.
- Compliance with specified tolerances and heat treatment processes is essential for optimal gear performance and longevity.
- Correct positioning of mounting and lubrication points is critical for maintenance and reliability.
Summary
This document provides comprehensive technical specifications and assembly guidelines for the DUO-ROL-X patented crown gears by GROUPE DEFONTAINE. It covers mechanical dimensions, manufacturing notes, heat treatment, and quality standards to ensure precise production and reliable assembly. The emphasis on confidentiality and proprietary rights reflects the specialized and sensitive nature of these mechanical components.
Catalog excerpts
Implantation according to A Ansicht nach A Tolérances générales suivant IT-ETR-061 et ISO 8015 General tolerances according to IT-ETR-061 and ISO 8015 Allgemeine toleranzen nach IT-ETR-061 und ISO 8015 Denture - Gear - Verzahnung Angle de pression Module - Modul Pressure angle Eingriffswinkel Diametral pitch Troncature Nbre de dents Truncature - Kopfkurzung Nr. of teeth - Zahnezahl Diamêtre primitif Pitch diameter - Teilkreissdurchmesser Déport 2 G m Add. mod. 2 Gm - Profilverschiebung 2 Gm Cote sur dents Measurement on teeth Zahnmessweite bei Zahnen Faux rond au diamêtre primitif - Run out on P.D. Rundlauffehler am Teilkreis Non trempée No hardened Ungehartet Trempée Hardened Gehartet Trous de fixation Mounting holes Befestigungsborungen Trous de fixation Mounting holes Befestigungsborungen Trous de graisseurs Grease holes Schmierborungen Trous de graisseurs Grease holes Schmierborungen Masse estimée Gewicht ca Estimated weight equid. equis. gl. Abst. equid. equis. gl. Abst. equid. equis. gl. Abst. equid. equis. C 21/09/1994 Montage était avec cage gl. Abst. Position approximative du bouchon et du raccord de trempe Filler plug and hardening connection of raceway ca Stopfen - und heertteschlupf - position B 28/01/1987 H. denture était 40 ; Date Cette couronne brevetée DUO-ROL-X est notre propriété. Ce plan ne peut être communiqué ni retransmis à des tiers sans l'autorisation écrite de ROLLIX-DEFONTAINE Information confidential proprietary of ROLLIX-DEFONTAINE. Any person excepted is required to accept same information in confidence and agrees to make no disclosures or use there of except as authorized by ROLLIX - DEFONTAINE Diese paterntierte drehverbindung DUOROL-X ist unser Eigentum. Diese zeiuchnung darf nicht ohne schriftliche genehmigung von ROLLIX-DEFONTAINE weitergegeben werden.
Open the catalog to page 1
Implantation suivant A Implantation according to A Tolérances générales suivant IT-ETR-061 et ISO 8015 General tolerances according to IT-ETR-061 and ISO 8015 Allgemeine toleranzen nach IT-ETR-061 und ISO 8015 Denture - Gear - Verzahnung Angle de pression Module - Modul Pressure angle Eingriffswinkel Diametral pitch Troncature Nbre de dents Truncature - Kopfkurzung Nr. of teeth - Zahnezahl Diamêtre primitif Pitch diameter - Teilkreissdurchmesser Déport 2 G m Add. mod. 2 Gm - Profilverschiebung 2 Gm Cote sur dents Measurement on teeth Zahnmessweite bei Zahnen Faux rond au diamêtre primitif - Run...
Open the catalog to page 2
Tolérances générales suivant IT-ETR-061 et ISO 8015 General tolerances according to IT-ETR-061 and ISO 8015 Allgemeine toleranzen nach IT-ETR-061 und ISO 8015 Denture - Gear - Verzahnung Angle de pression Module - Modul Pressure angle Eingriffswinkel Diametral pitch Troncature Nbre de dents Truncature - Kopfkurzung Nr. of teeth - Zahnezahl Diamêtre primitif Pitch diameter - Teilkreissdurchmesser Déport 2 G m Add. mod. 2 Gm - Profilverschiebung 2 Gm Cote sur dents Measurement on teeth Zahnmessweite bei Zahnen Faux rond au diamêtre primitif - Run out on P.D. Rundlauffehler am Teilkreis Non trempée...
Open the catalog to page 3
Tolérances générales suivant IT-ETR-061 et ISO 8015 General tolerances according to IT-ETR-061 and ISO 8015 Allgemeine toleranzen nach IT-ETR-061 und ISO 8015 Denture - Gear - Verzahnung Angle de pression Module - Modul Pressure angle Eingriffswinkel Diametral pitch Troncature Nbre de dents Truncature - Kopfkurzung Nr. of teeth - Zahnezahl Diamêtre primitif Pitch diameter - Teilkreissdurchmesser Déport 2 G m Add. mod. 2 Gm - Profilverschiebung 2 Gm Cote sur dents Measurement on teeth Zahnmessweite bei Zahnen Faux rond au diamêtre primitif - Run out on P.D. Rundlauffehler am Teilkreis Non trempée...
Open the catalog to page 4
Tolérances générales suivant IT-ETR-061 et ISO 8015 General tolerances according to IT-ETR-061 and ISO 8015 Allgemeine toleranzen nach IT-ETR-061 und ISO 8015 Denture - Gear - Verzahnung Angle de pression Module - Modul Pressure angle Eingriffswinkel Diametral pitch Troncature Nbre de dents Truncature - Kopfkurzung Nr. of teeth - Zahnezahl Diamêtre primitif Pitch diameter - Teilkreissdurchmesser Déport 2 G m Add. mod. 2 Gm - Profilverschiebung 2 Gm Cote sur dents Measurement on teeth Zahnmessweite bei Zahnen Faux rond au diamêtre primitif - Run out on P.D. Rundlauffehler am Teilkreis Non trempée...
Open the catalog to page 5
Tolérances générales suivant IT-ETR-061 et ISO 8015 General tolerances according to IT-ETR-061 and ISO 8015 Allgemeine toleranzen nach IT-ETR-061 und ISO 8015 Denture - Gear - Verzahnung Angle de pression Module - Modul Pressure angle Eingriffswinkel Diametral pitch Troncature Nbre de dents Truncature - Kopfkurzung Nr. of teeth - Zahnezahl Diamêtre primitif Pitch diameter - Teilkreissdurchmesser Déport 2 G m Add. mod. 2 Gm - Profilverschiebung 2 Gm Cote sur dents Measurement on teeth Zahnmessweite bei Zahnen Faux rond au diamêtre primitif - Run out on P.D. Rundlauffehler am Teilkreis Non trempée...
Open the catalog to page 6
Implantation suivant A Implantation according to A 0 Tolérances générales suivant IT-ETR-061 et ISO 8015 General tolerances according to IT-ETR-061 and ISO 8015 Allgemeine toleranzen nach IT-ETR-061 und ISO 8015 Denture - Gear - Verzahnung Angle de pression Module - Modul Pressure angle Eingriffswinkel Diametral pitch Troncature Nbre de dents Truncature - Kopfkurzung Nr. of teeth - Zahnezahl Diamêtre primitif Pitch diameter - Teilkreissdurchmesser Déport 2 G m Add. mod. 2 Gm - Profilverschiebung 2 Gm Cote sur dents Measurement on teeth Zahnmessweite bei Zahnen Faux rond au diamêtre primitif -...
Open the catalog to page 7All DEFONTAINE - ROLLIX catalogs and technical brochures
Rollix Spares & Services8 Pages
- DEFONTAINE slewing ring
- DEFONTAINE ball bearing slewing ring
- DEFONTAINE single-row slewing ring
- DEFONTAINE external-toothed slewing ring
- DEFONTAINE roller slewing ring
- DEFONTAINE slewing ring without teeth
- DEFONTAINE internal-toothed slewing ring
- DEFONTAINE precision slewing ring
- DEFONTAINE heavy load slewing ring
- DEFONTAINE axial slewing ring
- DEFONTAINE wind turbine slewing ring
- DEFONTAINE double-row slewing ring
- Robotic slewing ring
- DEFONTAINE crossed roller slewing ring
- DEFONTAINE forestry machinery slewing ring
- DEFONTAINE slewing ring for marine applications
- DEFONTAINE slewing ring for medical applications
- DEFONTAINE agricultural machinery slewing ring
- DEFONTAINE radial slewing ring
- DEFONTAINE materials handling slewing ring