Triple Threat™ Three Flute Rougher/Finisher, Inch
16Pages

{{requestButtons}}

Catalog excerpts

Triple Threat™ Three Flute Rougher/Finisher, Inch - 1

The Triple Threat" tool is a multi-patented three flute high performance carbide end mill designed to finish and rough in aluminum and non-ferrous metals. The high shear, 45 degree helix and improved inter-flute geometries enhanced chip evacuation and permit increased chip loads as well as aggressive feed rates. Aluminum Alloys Aluminum Cast Aluminum Sand & Permanent Mold >10% Silicon High Silicon Based Cast, Wrought Yellow, Red Leaded Brass Cast, Wrought HP = HEAVY PERIPHERAL Axial Depth up to Effective Length of Cut Radial width .3 x Diameter FINISH = FINISH OPERATION Axial Depth up to Effective Length of Cut Radial width .02 x Diameter LP = LIGHT PERIPHERAL Axial Depth up to Effective Length of Cut Radial width .01 x Diameter Note! Horsepower will be the limiting factor with larger diameter end mills. Horsepower = IPM x RDC x ADC x PC IPM = Inches Per Minute RDC = Radial Depth of Cut (Width) ADC = Axial Depth of Cut (Depth) PC = Power Constants (Aluminum = (0.25)) Example Slotting = 3/4 diameter x 3/8 @ 150 IPM HP = 150 IPM x .750 RDC x .375 ADC x PC of 0.25 HP = 10.8 @ cutter/80%Efficiency = 12.8 @ Spindle Motor

Open the catalog to page 1
Triple Threat™ Three Flute Rougher/Finisher, Inch - 2

The Triple Threat™ tool is a multi-patented three flute high performance carbide end mill designed to finish and rough in aluminum and non-ferrous metals. The high shear, 45 degree helix and improved inter-flute geometries enhanced chip evacuation and permit increased chip loads as well as aggressive feed rates. Feeds and Speeds Chart with Chip-Load per/tooth in Inches Materials Aluminum Alloys Aluminum Cast Sand & Permanent Mold >10%Silicon High Silicon Based Cast, Wrought Yellow, Red Leaded Brass Cast, Wrought HP = HEAVY PERIPHERAL Axial Depth up to Effective Length of Cut Radial width...

Open the catalog to page 2
Triple Threat™ Three Flute Rougher/Finisher, Inch - 3

Triple Threat™ Three Flute Rougher/Finisher, With Chip Breakers, Inch High Performance Carbide The Triple Threat" tool is a multi-patented three flute high performance carbide end mill designed to finish and rough in aluminum and non-ferrous metals. The high shear, 45 degree helix and improved inter-flute geometries enhanced chip evacuation and permit increased chip loads as well as aggressive feed rates. Materials Aluminum Alloys Aluminum Cast Aluminum Copper Brass Magnesium Diameter Description 6061,7075 Sand & >10%Silicon Cast, Wrought Yellow, Red Cast,...

Open the catalog to page 3
Triple Threat™ Three Flute Rougher/Finisher, Inch - 4

Triple Threat™ Three Flute Rougher/Finisher, With Chip Breakers, Metric The Triple Threat" tool is a multi-patented three flute high performance carbide end mill designed to finish and rough in aluminum and non-ferrous metals. The high shear, 45 degree helix and improved inter-flute geometries enhanced chip evacuation and permit increased chip loads as well as aggressive feed rates. • 45 Degree Helix for Enhanced Chip Evacuation • Available Upon Request: • Plain Cylindrical Shank m Coolant Grooves • Three Flutes Permit High Machine Productivity m Additional Coatings • Stocked Stub,...

Open the catalog to page 4
Triple Threat™ Three Flute Rougher/Finisher, Inch - 5

Technical Chart The ALDH is the rougher of choice when optimum material removal rates are the objective. The combination of progressive geometries result in a cutting tool intended for full engagement cuts at increased feed rates. Slotting cuts of lx the diameter or more are normally recommended. 50% greater IPM versus competitors 2 flute design is a conservative starting point. ALDH Materials Aluminum Alloys Aluminum Cast Aluminum Copper Brass Magnesium Diameter Description 6061,7075 Sand & >10% Silicon Cast, Wrought Yellow, Red, Cast, Wrought Permanent Mold High...

Open the catalog to page 5
Triple Threat™ Three Flute Rougher/Finisher, Inch - 6

Technical Chart ALDH-C series combines the performance of the ALDH series with a truncated knuckle form to manage chips and Horse Power. It is designed for freer cutting without sacrificing work piece surface finishes. This unique O.D. form also aids in chip control and management in gummy, non-ferrous materials. The tools are available from stock in stub and standard lengths with coatings to match your particular applications. Carbide Feeds and Speeds Chart for Non-Ferrous Materials ALDH-C Materials Aluminum Alloys Aluminum Cast Aluminum Copper Brass Magnesium Diameter...

Open the catalog to page 6
Triple Threat™ Three Flute Rougher/Finisher, Inch - 7

High Performance Carbide • Rough and Finish • Available Upon Request: • Higher Helix Aids in Chip Removal m Radius Ends • High Performance Carbide m Coolant Groves The ARF Series is a time-honored workhorse in our aluminum cutting tool family. Designed as a 2 flute, rougher/finisher, this tool can pull “double duty” in your aluminum and non-ferrous applications. The high helix angle provides exceptional shearing action and chip removal. Available in lengths ranging from stub for aggressive roughing, to extended lengths for tall side milling cuts. ARF Materials Aluminum Alloys...

Open the catalog to page 7
Triple Threat™ Three Flute Rougher/Finisher, Inch - 8

Technical Chart The HSM is a 2 flute rougher/finisher that uses the geometries of the ARF series and couples them with an extended reach design. The stub flute length, in conjunction with a wide range of reach lengths, makes the HSM series a great choice for roughing in aluminum and other non-ferrous materials in hard to reach depths of cuts. Carbide Feeds and Speeds Chart for Non-Ferrous Materials HSM Materials Aluminum Alloys Aluminum Cast Aluminum Copper Brass Magnesium Diameter Description 6061,7075 Sand & >10% Silicon Cast, Wrought Yellow, Red, Cast,...

Open the catalog to page 8
Triple Threat™ Three Flute Rougher/Finisher, Inch - 9

HVM-2, Two Flute Technical Chart The High Velocity Machining Series (HVM) is designed to perform at the level that its name suggests. By using shallow depths of cut, at very high speeds, this extended reach design will rough in non-ferrous applications from peripheral cuts to deep pockets. This tool is ideal for the machine tool that has ample RPM and feed rate capabilities, but may have some horsepower or torque restrictions. HVM-2 Materials Aluminum Alloys Aluminum Cast Aluminum Copper Brass Magnesium Diameter Description 6061,7075 Sand & >10% Silicon Cast, Wrought...

Open the catalog to page 9

All Data Flute CNC catalogs and technical brochures

  1. Aerospace

    104 Pages

  2. Triple Threat

    12 Pages

  3. HVMag Series

    4 Pages

  4. Aerospace

    96 Pages

Archived catalogs