Large Drill Attachment LEX050
19Pages

Large Drill Attachment LEX050 Congratulations on the purchase of your Darex XT-3000 Large Drill Attachment. (21 mm—30 mm) As part of the assembly (see picture from left to right) you should have a SA16565XA Large drill alignment, SA16575CA Sharpening fixture, and SA16500TA Large Drill Chuck. By now you are familiar with the ‘quick disconnect’ feature of your XT-3000. Start by placing the Large Drill Alignment on the top of your XT3000. Rotate the ‘Docking Lever’ clockwise to securely lock the fixture in place. In a similar manner, remove your current sharpening fixture and replace it with the Large Drill Sharpening alignment is adjusted by rotating the black lever located at on the front of the alignment fixture. As per the decal, rotating the lever towards the operator will reduce the amount of relief ground onto the drill and pushing the lever away from the operator will increase the relief. Placing the pin at the midway point on the decal is a good starting place for 118° drills. For 135°-150° drills start with the alignment 2 marks towards the operator. You can set the alignment at any setting necessary to achieve the amount of relief desired. Place the drill in the chuck and turn the chuck knob clockwise until the drill slides freely through the chuck jaws. Next slide the Chuck and drill into the alignment rotating the chuck until one of the ‘cam dogs’ aligns with the mating ‘notch’ in the fixture. Fixture. Now would be a great time to determine the point angle of the drill that is to be sharpened and adjust both the sharpening fixture and alignment to that point angle. The Sharpening fixture is adjusted by pulling the red lever towards (counter clockwise) the operator and sliding the fixture to the point angle desired. Lock the fixture by returning the red lever to its original position. The You will notice the opposite ‘dog’ aligns with a reference mark machined into the alignment fixture. Now push the drill through the chuck until it contacts the stop. Rotate the drill clockwise until

the outer edge of the cutting lip is touching the pins in the setting fixture. Firmly tighten the chuck by turning the knob clockwise while the chuck is still in the fixture. Remove the chuck and drill. The drill is now aligned and set to length to the chuck cam for the necessary grinding. Slide the chuck into the Sharpening fixture and rotate the Chuck clockwise applying slight pressure into the wheel. It is also necessary to keep the cam up against the swing cam follower bearing. Try to sharpen the drill in such a manner that the drill is off the wheel before you reposition your hand on...

Large Drill Attachment

Large Drill Attachment LEX050 SA16615BA Pivot Lock Lever Assembly PP16615BF Pivot lock lever PP16630FF 5mmX8mm SSS Timing Adjuster Assembly PP16283RF Material adjust spring PP16285TF Material adjust screw PP03924TF PS Latch Screw Handle PP16585TF Large Drill Timing Adjuster PP11015FF 1/8" Dowel Pins Feed Bearing Assembly PP16652TF Feed Bearing Bolt PP08560LF Bearing Swing Bearing Assembly PP16655LF Swing Bearing PP16657TF Swing Bearing Bolt Spring Tensioner Assembly PP16645TF Spring Tensioner PP12280FF M6 x 1 x 8mm SSS 21-30 MM Chuck PP16500TF Large chuck Body 21-30mm PP16505TF 21-30mm...

X-Y Table No Sub Assemblies, Send in for Repair 45

Countersink Instructions LEX150 Congratulations on the purchase of your Darex XT-3000 Countersink Attachment. This fixture comes with 2 V-40 double angle collets and is used in conjunction with the Darex XT-3000 X-Y Attachment. X-Axis Knob Pivot Lock Knob Y-Axis Knob By now you are familiar with the ‘quick disconnect’ feature of your XT-3000. Begin by removing the current sharpening fixture and replacing it with the X-Y table. Secure it in place by rotating the ‘Docking Lever’ clockwise. In a similar manner, lock the Countersink Attachment to the top of the machine. It is now necessary to...

To sharpen the tool, determine which angle the tool will be sharpened at. To adjust the X-Y table, loosen the Pivot Lock Knob and swing the table to that angle. Tighten the Pivot Lock Knob. Pivot Lock Knob Remove the Countersink Attachment from the top of the machine and place it on the X-Y Table. Again, rotate the Docking Lever clockwise to secure the fixture. Turn the machine ON. Using both the X and Y axis feed knobs, carefully position the cutter into the grinding wheel. Y-Axis Knob X-Axis Knob Once the tool touches the grind wheel, begin to rotate the spindle in a clockwise direction...

Countersink Attachment

Counter Sink Attachment LEX150 SA16823TA Alignment Thumb Screw CS Spindle lock assy. PP16830TF

BRAD POINT ATTACHMENT LEX200 Congratulations on the purchase of the Darex XT3000 Brad point Attachment. (LEX200) This attachment consists of 2 pieces, 1 Sharpening Fixture, SA16900BA and 1 - 3mm – 12mm Chuck, SA16916TA. (The 12mm – 21mm Chuck, SA16918TA is available as an optional accessory) Both components are laser marked with a Brad Point icon to minimize confusion with other XT3000 attachments. SETTING UP: To sharpen a Brad Point, you X-Axis Knob will have to remove the standard sharpening fixture and replace it Pivot Lock Knob with the X-Y Y-Axis Knob Table (LEX100). The Brad Point...

Brad Point Attachment 1/4-20 x 1 SSS Point angle lock knob Feed Bearing Bolt Feed Bearing

STEP DRILL ATTACHMENT LEX 250 Congratulations on the purchase of your Darex XT- 3000 Step Drill Attachment. (LEX250). This attachment consists of 3 pieces, 1 Sharpening Fixture, SA16950BA, 1 Alignment Fixture, SA116970XA and a 3mm – 12 mm Chuck, SA16975TA. (The 12mm – 21mm Chuck, SA16980TA is available as an optional accessory) All 3 components are laser marked with a Step Drill icon to minimize confusion with other XT3000 attachments. the XT-3000. Rotate the Docking Lever CW to secure the X-Y Table to the XT-3000. X-Axis Knob Pivot Lock Knob Y-Axis Knob In a similar manner, lock the Step...