DSSIU-6-1U Dedicated 6-channel system interface unit for ultra-stable, high precision fluxgate technology current transducers. Powers up to 6 x DS50 to DL2000 at the same time. Compact 19” rack mount 1U height Current transducers’ output signals available via 4mm banana plugs Individual or serial access to calibration windings of all 6 transducers via 4mm banana plugs 15-pin DSUB connector provides access to isolated status signals of each transducer and power Front LEDs indication of normal operation for each transducer and power LED for DSSIU-6-1U Universal autorange (100-240V AC 50-60Hz) AC input voltage or 127–370V DC input voltage. Precision – Innovation www.dani

Mains input AC input voltage Power rating Transducer output port Supply voltage Ripple Reverse collector emitter voltage, off Status Port (Isolated output) Collector-Emitter current 100-240V~ ±10% "~" refers to EN61010-1 table 1,symbol 2 meaning alternating current Exception for DL2000ID and DL2000UB-1V : DSSIU-6-1U can only handle 4 pcs. DL2000ID/DL2000UB1V at low voltage input 115V. With high voltage input 230V the DSSIU-6-1U can handle 6 pcs. DL2000ID/ Channel configuration Each channel does have 5 connectors. • Transducer (DSUB9) for connection to the transducer • YELLOW Calibration + (4mm...

DSSIU-6-1U Environmental, safety and mechanical specifications Parameter Polution Degree Ambient operating temperature range Storage temperature range Relative humidity DSUB9 female for transducer connection 4mm banana (red and black) jacks for output of measured current from transducers 4mm banana (Yellow) jacks for connection of calibration current to transducer DSUB15 female for status information IEC inlet for mains connection External devices Only connect Danisense transducers to the DSSIU-6-1U The unit should only be cleaned with a damp cloth. No detergent or chemicals should be used. Caution:...

DSSIU-6-1U Calibration winding access Each channel gives access to the calibration winding of transducers with this feature. Currently the following transducers do support this functionality. • • • • DS200ID-CD1000 - 1000 turns calibration winding (Max 200mA) - Equals a primary current of 200A DS200ID-CD100 - 100 turns calibration winding (Max 100mA) - Equals a primary current of 10A DS600ID-CD100 - 100 turns calibration winding (Max 100mA) - Equals a primary current of 10A DL2000ID-CD100 - 100 turns calibration winding (Max 100mA) - Equals a primary current of 10A Each transducers calibration...

Package content • • • • • 2m mains power cable—region specific DSSIU-6-1U 4 x rubber feet 4 x Rack screws with nuts Manual / Datasheet Precision – Innovation www.danisense.

DSSIU-6-1U User Guide Intended use: The DSSIU-6-1U is designed to work with Danisense transducers with DSUB9 connection powered by +/-15V. Instruction for use: 1.Do not power up the device before all cables are connected. 2.Only use cable provided by Danisense to ensure correct wiring and dimension of cable. 3.Ensure that it is easy to unplug the mains cord in case of system problems. 4.Place the primary conductor through the apperture of the transducer(s) 5.If the DSSIU-6-1U is intended for desk use, mount the rubber feet which are part of the package. 6.If the DSSIU-6-1U is intended for Rack...

Danisense A/S Malervej 10 DK-2630 Taastrup Denmark Declares that under our sole responsibility that this product is in conformity with the provisions of the following EC Directives, including all amendments, and with national legislation implementing these directives: Directive 2014/30/EU Directive 2014/35/EU And that the following harmonized standards have been applied EN 61010-1 (Third Edition):2010, EN 61010-1:2010/A1:2019 EN 61010-2-030:2021/A11:2021 EN 61326-1:2013 All DANISENSE products are manufactured in accordance with RoHS directive 2011/65/EU. Annex II of the RoHS directive was amended...