DR5000IM High precision fluxgate AC/DC current transducer for galvanically isolated measurement up to 8000 A Features • 5000 A rms nominal current • 2500 :1 primary/secondary current ratio • Current output through banana jacks • Ø150 mm aperture • 4 ppm total accuracy • 1 ppm linearity • 3 ppm offset • Status signal and LED • Control unit included Description High precision DC current transducer (DCCT) measuring up to 8000 A currents and continuously measuring 8000 A currents with a linearity error less than 1 ppm. Based on the ultra stable Danisense closed loop flux gate technology, the DR5000IM has very low offset and ultra low drift. The DR5000IM system consists of a sensor head and a mains powered control unit, connected by cable with • Wind, solar and energy • Electric vehicle (EV) test bench • Power measurement and power analysis • Battery testing and evaluation systems • Current calibration purposes • Stable power supplies multiple length options. It provides high resolution for precise monitoring, • Precision current sensing reliable and consistent performance, and a rugged design for durability. All information subject to change without notice

DR5000IM Electrical specifications at 23 °C, Vs = ± 15 V supply voltage Parameter Nominal primary AC current Nominal primary DC current At nominal primary DC current Iprimary /Isecondary Measuring range Overload capacity Nominal secondary current Primary / secondary ratio Measuring resistance Linearity error Offset current (including earth field) Offset temperature coefficient Offset stability over time Bandwidth Response time to a step current IPN Total accuracy without offset Phase shift From 10% to 90% of step current % of reading + % of full scale For details, see Reading and full For other...

DR5000IM Linearity error Linearity error is defined as the deviation from a straight line. The max current and another trendline is calculated from 0 to negative max current. The difference between each measured point and the squares method of the measurement points from 0 to positive Measurement Trendline linear trend line is the linearity error. The linearity error L can be expressed as (1), where Ireading is the measurement result Dato: 15. Novemberand 2012 Ifitted Linearity error straight line is a linear regression trend line based on the least Figure 1: Linearity error definition Reading...

Primary DC and peak current (A) Figure 2: Maximum measurement resistor RM vs. ambient temperatures Primary current (Arms) Figure 3: Maximum continuous primary current vs. frequency Figure 4: Frequency characteristics All information subject to change without notice

DR5000IM Isolation specifications according to IEC 61010-1 When using REINFORCED insulated wire, all wiring must be insulated for the highest voltage used. When using BASIC insulated or uninsulated wire, follow the specified voltages in the table below: Parameter Creepage distance Comparative tracking index (CTI) Continuous working voltage according to IEC 61010-1 with: Uninsulated wire: CAT III (dc and rms) BASIC insulated wire: Transient voltage according to IEC 61010-1 with: Uninsulated wire: CAT III BASIC insulated wire: Do not connect the transducer to signals or use for measurements within...

The transducer should only be cleaned with a damp cloth. No detergent or chemicals should be used. When multiple primary turns are used or high primary currents are applied the temperature around the transducer will increase, please monitor to ensure that the maximum ratings are not exceeded. It is recommended to have minimum 1 mm2 per ampere in the primary bus bar. The DR5000IM is designed to measure current up to 8000 A. Please see the product manual: https://danisense.com/user-manual Safety instructions If the equipment is used in a manner not specified by the manufacturer, the protection...

DR5000IM • Unit is powered and secondary circuit is open or interrupted Both DC and AC primary current up to 100% of nominal value can be applied to the current transducers in the above situations without damage to the electronics. Please notice that the transducer core can be magnetized in all above cases, leading to a small change in output offset current (less than 10ppm) Package content • Transducer head (DS5000) • Electronics control box (DSCU-1) 19” 2U rack mountable • AC power cable - region specific • 5 m cable for connecting DS5000 and DSCU-1 (Other lengths available upon request, pricing...

Voltage output Status Port Transducer Head Warning This apparatus must be earthed To prevent electric shock, disconnect AC line before removing cover Figure 6: Dimensions of electronics control box. 0.3 mm general tolerance Base plate mounting (Transducer head): 4 x 8 mm slotted holes, 6 Positive current direction DRAWN CHECKED Is identified by a label on the housing.NNN APPR Figure 7: D-sub-9 connection pinout DD-MM-YYYY DD-MM-YYYY SCALE When the sensor is operating in normal condition the status pins 1:4 Document number General tolerances: ± 0.1 Status signal and LED (Status+ and Status-) are...

Declaration of Conformity Danisense A/S Malervej 10 DK-2630 Taastrup Dato: 15. November 2012 Declares that under our sole responsibility that this product is in conformity with the provisions of the following EC Directives, including all amendments, and with national legislation implementing these directives: Directive 2014/30/EU Directive 2014/35/EU And that the following harmonized standards have been applied EEN 61010-1 (Third Edition):2010, EN 61010-1:2010/A1:2019 EN 61010-2-030:2021/A11:2021 EN 61326-1:2013 All DANISENSE products are manufactured in accordance with RoHS directive 2011/65/EU....