*mydirectindustry

Catalogs
Danisense
DQ600ID-P1300

DQ600ID-P1300

Product catalog summary

Features and Applications
The DQ600ID-P1300 is a high precision current transducer using fluxgate technology for non-intrusive, isolated DC and AC current measurement up to 1300A. Key features include a maximum linearity error of 1 ppm, single supply of 15V, and a full aluminum body for superior EMI shielding. It is suitable for applications such as particle accelerators, MRI devices, precision drives, and power analysis.

Specifications
The transducer supports a nominal primary AC current of 600 Arms and DC current of -900 to 900 A, with a measuring range of -1300 to 1300 A. It has a primary to secondary ratio of 1:1500 and operates within a temperature range of -40°C to 85°C. The device is designed to handle overloads up to 4500 A for 100ms.

Electrical Characteristics
At 23°C and a supply voltage of +15V, the transducer exhibits a bandwidth of 300 kHz and a response time of 1 µs. It maintains accuracy with a DC-10Hz overall accuracy of ±11 ppm and an AC maximum gain error of ±0.07% from 10Hz to 2kHz.

Isolation and Safety
The device features a clearance of 9 mm and a creepage distance of 10 mm, with an impulse withstand voltage of 10.4 kV. It complies with IEC 61010-1 and EN50780 standards for reinforced isolation.

Advanced Sensor Protection Circuits (ASPC)
The ASPC protects the transducer from fault conditions, allowing primary currents up to 100% of nominal value without damage. However, the sensor core may become magnetized, causing a minor offset change.

Accessories and Connectivity
Accessories include power supply units for multiple transducers and various lengths of transducer cables. The DSUB-9 pin layout is used for connections, with status pins indicating normal operation.

Compliance and Standards
The product complies with EC Directives 2014/30/EU and 2014/35/EU, and adheres to RoHS directive 2011/65/EU. It is manufactured following EN 63000:2018 provisions.

Catalog excerpts

dani/enseUltra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1300A Applications: MPS for particles accelerators Gradient amplifiers for MRI devices Stable power supplies Precision drives Batteries testing and evaluation systems Power measurement and power analysis Current calibration purposes Features Linearity error maximum 1 ppm Single Supply 15V Industry standard DSUB 9 pin connection Green diode for normal operation indication Full aluminum body for superior EMI shielding and extended operating temperature range Large aperture ^27.6mm for cables and bus bars All ppm (or %) values refer to nominal current Precision - Innovation www.danisense.com

Open the catalog to page 1

dani/enseElectrical specifications at Ta=23°C, supply voltage = +15V unless otherwise stated Parameter Precision - Innovation www.danisense.com

Open the catalog to page 2

DQ600ID-P1300 Measurement resistor RM and ambient temperature derating (Fig. 1) Maximum measurement resistor Value (Ohm) Maximum measurement resistor vs. ambient temperatures 20 15 10 5 0 600 Primary Current, peak or DC (A) R_max_25 Frequency and ambient temperature derating (Fig. 2) Maximum primary current A rms Primary Current (A) Primary Current (Hz) Max current (Arms) 85 deg Precision – Innovation www.danisense.com

Open the catalog to page 3

dani/ense Isolation specifications Precision - Innovation www.danisense.com

Open the catalog to page 4

DQ600ID-P1300 Advanced Sensor Protection Circuits "ASPC" Developed to protect the current transducer from typical fault conditions: • Unit is un-powered and secondary circuit is open or closed • Unit is powered and secondary circuit is open or interrupted Both DC and AC primary current up to 100% of nominal value can be applied to the current transducers in the above situations without damage to the electronics. Please notice that the sensor core can be magnetized in all above cases, leading to a small change in output offset current (less than 10ppm) Status pins When transducer is operating...

Open the catalog to page 5

dani/ense (general tolerance 0.3mm unless otherwise statd) DSUB pin layout Standard DSUB-9 current output When sensor is operating in normal condition the status pins are shorted. - Maximum forward current 10mA - Maximum forward voltage 60V - Maximum reverse voltage 5V Status Status NC NC Out+ Out- Positive current directionIs identified by an arrow on the transducer body page 6 - 2022-11-24 Precision - Innovation www.danisense.com

Open the catalog to page 6

DQ600ID-P1300 Declaration of Conformity Danisense A/S Malervej 10 DK-2630 Taastrup Denmark Declares that under our sole responsibility that this product is in conformity with the provisions of the following EC Directives, including all amendments, and with national legislation implementing these directives: Directive 2014/30/EU Directive 2014/35/EU And that the following harmonized standards have been applied EN 61010-1 (Third Edition):2010, EN 61010-1:2010/A1:2019 EN 61010-2-030:2021/A11:2021 EN 61326-1:2013 All DANISENSE products are manufactured in accordance with RoHS directive 2011/65/EU....

Open the catalog to page 7

DQ600ID-P1300

DQ600ID-P1300

Catalog excerpts

All Danisense catalogs and technical brochures