ELIIXA+ 16k/8k CXP Cmos Multi-Line Colour Camera Cmos Colour Sensor :  16384 RGB Pixels, 5 x 5µm (Full Definition)  8192 RGB Pixels 10x10µm (True Colour) Interface : CoaXPress® (4x 6Gb/sLinks) Line Rate :  Up to 47500 l/s In 16k Full Definition Mode  Up to 95000 l/s in 8k True Colour Mode Bit Depth : 24bits (RGB 8bits) Efficient color interpolation Scan Direction Flat Field Correction Low Power Consumption : <19W Compliant with Standard Lenses of the Market Description e2v’s next generation of line scan cameras are setting new, high standards for line rate and image quality. Thanks to e2v’s recently developed multi-line CMOS technology, the camera provides an unmatched 95,000 lines/s and combines high response with an extremely low noise level; this delivers high signal to noise ratio even when short integration times are required or when illumination is limited. The 5μm pixel size is arranged in four active lines and dual line filter configuration allowing the camera to be operated in several modes: True colour mode with 10μm RGB pixels to provide equivalent colour fidelity to 10μm pixel tri-linear solutions with advanced immunity to web variation or Full definition mode with a unique16,384 RGB pixel resolution. Printing Inspection High Resolution Document Scanning Printed Circuit Board Inspection Flat Panel Display Inspection

Key Specifications Characteristics Typical Value Sensor Characteristics at Maximum Pixel Rate Resolution 16384 8192 pixel size (square) 5 10 Max line rate 47.5 95 Radiometric Performance at Maximum Pixel Rate and minimum camera gain Bit depth 3x8 Response non linearity <1 PRNU HF Max 3 Dynamic range 65 Response (Peak) : True Color or Full Def. Enhanced Red 11.8 Green 11.2 Blue 7.8 Functionality (Programmable via GenICam Control Interface) Analog Gain Up to 12 (x4) dB Offset -4096 to +4096 LSB Trigger Mode Timed (Free run) and triggered (Ext Trig, Ext ITC) modes Sensor Modes  True Color Enhanced...

Image Sensor The Eliixa+ Colour 16k sensor is composed of two pairs of sensitive lines. The Colour version has been completed with RGB colour Filter and disposed as detailed beside. Each pair of lines use the same Analog to Digital Column converter (ADC Column). An appropriate (embedded) Time delay in the exposure between each line this allows to combine two successive exposures in order to double the sensitivity of a single line. This Time Delay Exposure is used only in the Full Definition Enhanced. ADC Column Intermediate Blind Pixel Pixel Line A Pixel Line B Pixel Line C Pixel Line D Intermediate...

Full Definition Enhanced Mode (FDE) 5µm Pixels (R,G,B) Same definition than B&W Requires x3 the data flow of the B&W  Sensitivity is the same as the TC mode available : Equivalent to 6 x Pixels of 5µm (with their respective colour filters). Pixel 5µm {RGB} Delay : 1 line of 5µm “Full Exposure control” is activated in this mode as the Time Delay Exposure is active. Color Interpolation in Full Definition modes. This color mode (5µm) requires the indication of “Forward/Reverse” to the camera in order to manage the delay between the two coloured lines.

True Colour Enhanced Mode (TCE) Double Blue : Vertical Binning Twice less pixels than B/W Double Red : Vertical Binning Requires x3/2 the data flow of B&W Pixel 10µm {RGB} High Sensitivity True Color mode: Equivalent to 6 x Pixels of 5µm (with their respective colour filters). “Full Exposure control” not needed in TC as the TDI is not active (only binning). The Exposure time can be control as for a single line mode. Double Green : Vertical Binning Double Green : Vertical Binning Web Direction Green Pixels averaging True Colour Single Mode (TCS) 10µm Pixels (R,G,B) Twice less pixels than B/W Single...

Column Interpolation Correction This interpolation is used to compensate the color error in the Red or the Blue in case of a vertical transition on the web : The Red of the blue value of each colored pixel is corrected if the variation between two neighbour green pixels is significant. B1’ = αB x B1 and R2’ = αR x R2 and It can be disabled by the customer. By default, it is enabled. This interpolation is available for all pixel sizes : 5x5µm but also 10x10µm αB is the blue correction, calculated with the variation (G1–G2) αR is the red correction, calculated with the variation (G1–G2) Line Interpolation...

Response & QE curves Quantum Efficiency Spectral Response Curve Spectral response (Single Modes) Green blue

Spectral response (Enhanced Modes) Green blue

Hardware Mechanical Drawing

Trigger Connector Multi-Colored LED for Status and diagnostic CoaXPress Connectors Power Over CoaXPress The ELIIXA+ CXP is compliant with the Power Over CoaXPress : There is no Power connector as the power is delivered through the Coaxial Connectors 1 and 2. In the Standard, the Power Over CoaXPress allows to deliver 13W (under 24V) per Channel. The ELIIXA+ CXP requires 19W then two connectors are required for the power : The two first are used for this purpose. If you want to Power ON the Camera you have to connect the Coaxial connector output 1 of the camera to the coaxial connector 1 of the...

Trigger Connector Camera connector type:Hirose HR10A-7R-5SB or compliant Cable connector type: Hirose HR10A-7P-5P (male) or compliant, Provided with the Camera Signal LVDS IN1+ / TTL IN1 LVDS IN1LVDS IN2+ / TTL IN2 LVDS IN2GND Receptacle viewed from camera back IN1/IN2 are connected respectively to Line0/Line1 and allow to get external line triggers or the forward/Reverse “Live” indication. On the Connector side, the 120Ω termination is validated only if the input is switched in LVDS or RS422. The electrical schematic is detailed below :

Standard Conformity The ELIIXA+ cameras have been tested using the following equipment:  A shielded Trigger cable A 10m CoaXPress Cable for the data transfer, certified at 6Gb/s e2v recommends using the same configuration to ensure the compliance with the following standards. CE Conformity The ELIIXA+ cameras comply with the requirements of the EMC (European) directive 89/336/CEE (EN50081-2, EN 61000-6-2). FCC Conformity The ELIIXA+ cameras further comply with Part 15 of the FCC rules, which states that: Operation is subject to the following two conditions:  This device may not cause harmful...