EcoRich R A fusion of hydraulic and motor/inverter technologies Drastically improved functions on top of the energy saving features of the IPM motor Hybrid hydraulic system Model list System configuration System for saving energy Description of function Optional functions Nomenclature Specifications Representative pressure – flow rate characteristics External dimension diagram Wiring guide Case studies of energy savings Energy-saving technologies supporting the hybrid hydraulic system Excluded from high-efficiency motor regulations

Model List Hybrid hydraulic system Diverse specifications for machine variations. Daikin’s hybrid hydraulic system lineup provides a variety of functions and capacities depending on the machine type. Equivalent to 0.75 kW Unit type Super Unit For general i ndustri al machi nes Super EcoRich Communication function Idling stop Maximum operating pressure (MPa) Rated capacity Analog command input Only applicable to single pumps. Maximum discharge rate (L/min) 15 * The above motor capacities are given for guidance only and do not represent the standard capacities of general motors. Excellent energy...

System configuration Control valve Control valve Pressure Rotational position, current Constant-speed induction motor Controller (inverter) Variable displacement piston pump Conventional hydraulic system Compact fixed-displacement pump Energy-saving and low heat/noise generation  The high-efficiency IPM motor is always controlled to run at an optimum speed with the inverter technology, eliminating unnecessary energy consumption.  The motor is controlled at the minimum required rotation speed to prevent unnecessary oil temperature rise and suppress deterioration of the hydraulic oil.  Running...

1 Further energy savings with high-efficiency IPM motor installed. The system uses an ultra energy-saving IPM motor*, featuring a combination of magnet torque (pull-in and repulsive force between a coil and permanent magnet) and reluctance torque (pull-in force between *IPM motor: Interior Permanent Magnet Synchronous Motor a coil and iron). Refer to Page 9 for details on the IPM motor. Power consumption 2 Low noise level at 50 dB (A) achieved in the pressure holding mode 3 EcoRich R is excluded from high-efficiency motor regulations. High-efficiency motor regulations came into effect in Japan...

16 pressure (P) - flow rate (Q) setting patterns are available for cylinder control.  The proportional control valve and proportional pressure control valve, which are utilized in conventional actuator circuits, can be omitted.  The pressure and flow rate can be set using the control unit’s operation panel.  The pressure and flow rate settings can be selected from among the 16 patterns using external input signals.  The EcoRich R autonomously switches between the pressure control and flow rate control modes. Shockless switching of flow rates and pressures  Setting the acceleration/deceleration...

*1: • The maximum flow rate is the theoretical value, not the guaranteed value. • Refer to the Delivery Specification (outside drawing) for detailed specifications. • This hydraulic unit is equipped with built-in safety valves. *2: • Use of hydraulic oils other than mineral-oil base type (e.g. hydrous/synthetic), water-glycol hydraulic oil for example, is prohibited. G Representative pressure - flow rate characteristics

External dimension diagram Do not place any obstacles to oil cooler air intake and exhaust within a distance of 100 mm from end faces of the unit. Install the unit at a location with good air flow so that heated air can be vented and take care about the temperature of the suction air: it must satisfy the stipulated condition for ambient temperature. EHU15R-M0701, EHU30R-M0701 DR1 Rp1 (above oil level) (Fitted with a vinyl cap at shipment) DR2 Rp¾ (above oil level) (Fitted with a vinyl cap at shipment) List of parts Name Oil tank Suction strainer Oil level gauge Inverter driven motor pump Controller...

EHU15R-M0701, M0702 EHU30R-M0701, M0702 I/O signal terminal block Terminal Terminal code Type Signal name (The above figure shows the normal status of the relay contacts.) * The switching capacity of the contact output is DC 30 V, 0.5 A (at resistance load). * The minimum applicable load of the contact output is DC 10 mV, 10 pA, but this is only a guide to the lower limit where switching is possible with a minute load. The value varies depending on the switching frequency, environmental conditions, etc., so it is advisable to check the actual value.

Machining center Conventional hydraulic unit Hobbing machine Conventional hydraulic unit NC milling machine ■ Conventional hydraulic unit EcoRich R Conventional hydraulic unit Conventional hydraulic unit: 75dB (A) on average EcoRich R : 71dB (A) on average Measurement distance : Proximity of 10 cm (for reference) (Thread grinding machine)

Energy-saving technology that supports hybrid hydraulic systems Daikin was the first in the industry to introduce an interior permanent magnet synchronous motor (IPM motor) into air conditioners for household use. Daikin was also an early adopter in the industry of the IPM motor for use in industrial-use air conditioners. We have led the industry as a front runner in air conditioner energy-saving performance. “Double torque” improves the energy-saving effect. Combining two rotational forces, “magnetic torque” generated by a powerful neodymium magnet* 1 and “reluctance torque”* 2 , generates...

Handling of EcoRich R The following are the minimum requirements for use of the EcoRich R. For details, refer to the unit’s Instruction Manual. Ambient conditions 1. Ambient temperature: 0 to 40°C, ambient humidity: 85%RH maximum (with no condensation), altitude: 1,000 m maximum, to be used indoors Hydraulic oil 1. Use mineral-oil base hydraulic oil. Use of hydraulic oils other than mineral-oil based type (e.g. hydrous/synthetic) is prohibited. 2. Use hydraulic oil equivalent to ISO VG32 to 68. Keep the viscosity of the hydraulic oil within the range from 15 to 400 mm2/s, and keep tank oil...