Penny & Giles Technical InformationSRH301 & SRH302 • Non-contacting Hall-effect technology • Simple mounting, low-profile design • Single- or dual-redundant-output options • Fail-safe outputs • AMP or Deutsch connector options • Flying-lead option • Protective cable-conduit option The SRH301 and SRH302 range of shaft-operated Rotary Position Sensors offers the optimal combination of performance, safety and cost. The sensor utilises proven Hall-effect, sensing technology in a low-profile (17.3mm) housing with integral magnet. The circuit design allows the sensor to be run from a regulated 5V supply or a varying voltage in the range of 930V, such as a vehicle's battery. The electrical output span can be set to correspond to rotations of 20° to 360°, and the positional information is determined by the angle of the integral magnet relative to the sensor. The integral magnet arrangement ensures a consistent sensor-magnet separation, avoiding errors associated with air-gap fluctuations. The SRH301 range has a single output, while the SRH302 contains two completely independent measuring circuits, each with its own power supply, meaning high-performing, safety-critical applications can easily be addressed. The versatile, factory-programmable electronics can be easily set to one of two analog voltage output ranges or one of three PWM frequencies. In addition, the polarities of each of the analog outputs can be independently set. The SRH301 and SRH302 both contain on-board diagnostic functions that mean the outputs can be put into safe, pre-defined states should an internal sensor error be detected. The sealed design offers exceptional levels of performance with respect to water and dust, shock, vibration and temperature, meaning the sensor is ideal for use in hostile, on- and off-highway vehicle environments. Connection options are industry-standard AMP Superseal or Deutsch DT04 series connectors, or simple flying leads for customer termination. The sensor can also be supplied with a protective conduit for the cabling.

© 2023 Curtiss-Wright. All rights reserved. Curtiss-Wright accepts no responsibility for possible errors in catalogs, brochures and other printed material. CurtissWright reserves the right to alter its products without prior notice. This also applies to products already ordered provided that such alterations can be made without affecting agreed specifications. All trademarks in this material are properties of their respective owners. 2 | Page

Description Analog voltage: 10-90% of 5V supply or 0.5-4.5V of 9-30V supply Analog voltage: 4-96% of 5V supply or 0.2-4.8V of 9-30V supply PWM: 244Hz PWM: 500Hz

Code Description 5 SRH302: Output 1 clockwise, Output 2 anti-clockwise SENSOR IS AT MID ELECTRICAL ANGLE WHEN SHAFT IDENT AND CABLE EXIT ARE ALIGNED AS SHOWN SHAFTIDENT IS IN THIS POSITION AT MID SHAFT FLAT IS IN THIS POSITION AT MID

Code Description NC0 No conduit, no connector (flying-leads) NC1 No conduit, Deutsch DT04 connector NC2 No conduit, AMP Superseal connector CC0 Conduit fitted, no connector (flying-leads) CC1 Conduit fitted, Deutsch DT04 connector CC2 Conduit fitted, AMP Superseal connector

INSTALLATION MECHANICAL Deutsch connector shown AMP connector option cable length as per illustrated for Deutsch connector Flying-lead option cable length 250-300 from datum A Dimensions in mm unless stated otherwise

Flying-Leads (XC0) Color Function RED SRH301: Vsupply Deutsch DT04 (XC1)SRH301 Deutsch DT04 3P-CE03 with gold contact 0460-202-1631 Mating Part No: DT06-3S-**** (plug) & 0462-201-1631 (pins) Deutsch DT04 6P-CE03 with gold contact 0460-202-1631 Mating Part No: DT06-6S-**** (plug) & 0462-201-1631 (pins)

AMP Superseal (XC2) SRH301 AMP 1.5 Superseal 282105-1 Mating Part No: 282087-X (plug) & 183025-1 (pins) SRH302 AMP 1.5 Superseal 282108-1 Mating Part No: 282090-X (plug) & 183025-1 (pins)

SPECIFICATIONS ELECTRICAL MEASUREMENT RANGE SUPPLY VOLTAGE SUPPLY CURRENT SUPPLY REVERSE POLARITY PROTECTION SHORT-CIRCUIT PROTECTION TO SUPPLY when used with 5V supply only OVER-VOLTAGE PROTECTION POWER-ON SETTLEMENT LINEARITY (ABSOLUTE) TEMPERATURE COEFFICIENT VOLTAGE OUTPUTS OUTPUT RANGE A1 (5Vdc SUPPLY) 10-90% ±1% of Vsupply over measurement range OUTPUT RANGE A1 (9-30Vdc SUPPLY) 0-5-4.5V ±3% absolute over measurement range MONOTONIC RANGE OUTPUT RANGE A5 (5Vdc SUPPLY) 4-96% ±1% of Vsupply over measurement range OUTPUT RANGE A5 (9-30Vdc SUPPLY) 0.2-4.8V ±3% absolute over measurement range...

DUTY CYCLE MONOTONIC RANGE LOAD RESISTANCE 0V and 5V ±3% nominal 10-90% over measurement range 5-95% nominal 10kQ min. (resistive to GND) <15|js typical t = PULSE WIDTH (INCREASES WITH I SHAFT DIRECTION CODE) MECHANICAL ANGLE MAXIMUM OPERATING SPEED 2x holes to suit M4 screws tightened to 2.9Nm 18AWG 1.65mm OD

ENVIRONMENTAL OPERATING TEMPERATURE RANGE 5V SUPPLY 9-30V SUPPLY -40°C to 140°C (-40°C to 120°C if conduit fitted) -40°C to 135.7°C at 9V, derate by 1.7°C for each 1V increase STORAGE TEMPERATURE RANGE Sensor body IP69K with conduit, IP68 without conduit Manufacturer ratings apply for connectors ELECTROMAGNETIC INTERFERENCE MAX OPERATING TEMPERATURE DERATING IMPORTANT INFORMATION Whilst Curtiss-Wright Industrial Division - Penny & Giles has designed this sensor to meet a range of applications it is the responsibility of the customer to ensure it meets their specific requirement. Penny & Giles...