Penny & Giles • Extremely robust design for arduous applications • Center detent for enhanced return-to-center performance • Under panel depth has been minimized to 78mm • Pivot-point position minimizes grip cable flex • Rated for 5 million cycles • Hall-effect sensor technology • Dual outputs with sense options • More functions, e.g. CAN interface, to follow • Multiple grip options ... The JC8000 offers high mechanical strength for very heavy-duty applications and features a center detent that provides guaranteed return-to-center, as well as a positive feel to the operator, throughout 5 million cycles. While maintaining an overall minimum underpanel depth of the joystick body, the shaft pivot-point position has been designed to be as low as possible so as to ensure a high strength capability in the small body space envelope. This reduction in angular deflection reduces wear on base-to-grip wiring, so enhancing overall reliability. Hall-effect sensing eliminates contact wear and provides safety functionality via dual outputs, which can be set to positive or negative ramps, or a combination of both. Electronic robustness is assured with sealing of the internal PCB to a rating of IP69k. A choice of multi-function grips are available, plus the option of ‘base-only’ enabling custom grips to be fitted. Beyond this initial release, further models will be introduced to provide increased grip functionality, CAN bus interfaces and mechanical variation.

© 2023 Curtiss-Wright. All rights reserved. Curtiss-Wright accepts no responsibility for possible errors in catalogs, brochures and other printed material. Curtiss-Wright reserves the right to alter its products without prior notice. This also applies to products already Ordered provided that such alterations can be made without affecting agreed specifications. All trademarks in this material are properties of their respective owners. 2 | Page

The ordering configuration is made up of the product name, followed by a multi digit code. The code is generated by the configuration required for each aspect of the joystick. Code Supply Voltage Min Output Voltage Center Voltage 10% 50%

CODE DESCRIPTION PP Output 1: Positive Slope Output 2: Positive Slope PN Output 1: Positive Slope Output 2: Negative Slope NP Output 1: Negative Slope Output 2: Positive Slope

Code Description NHA0 No grip, extended operating rod NHFL No grip, 13x flying leads (cable type 30AWG - 19/0.06, PTFE, Uni-Lay) NHAF No grip, extended operating rod, 13x flying leads (cable type 30AWG - 19/0.06, PTFE, Uni-Lay) (1) Refer to the relevant grip specification for configuration details. The overall performance of the joystick may be limited by the grip chosen (refer to grip specification). It is the responsibility of the customer when fitting the grip to ensure wires are correctly terminated (flying lead version only).

ROCKER OUTPUT JC8000-XX-X-XX-X-X-XXXX-X-XXXX-X-X-X-X Code NOTES AMF grip only. ROCKER PROFILE JC8000-XX-X-XX-X-X-XXXX-X-XXXX-X-X-X-X Code NOTES AMF grip only. NOTES The ‘N’ option is not available with the HKN, MGMF, AMF & HE grip options. Molex Mini-Fit 22-way – (5557 series) NOTES Gold plated contacts should be used in the mating connector.

INSTALLATION MECHANICAL The joystick is designed to be fitted from below the mounting panel through a 72mm diameter hole. The effectiveness of the joystick flange sealing is dependent on the panel mounting surface being sufficiently rigid to compress the sealing boot. The surface finish of the mounting panel is critical to achieve an adequate seal and rough surface finishes, paint chips, deep scratches, etc. should be avoided. Panel thickness: 3.5–4.5mm Screw torque (using supplied screws): 5Nm

ELECTRICAL CONNECTIONS 22-Way Joystick Connector Molex Mini Fit 22-way – (5557 Series) Pin See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification See chosen grip specification NOTES Gold plated contacts should be used in the mating connector. Base-to-Grip Connections 22-way Molex to flying leads....

SPECIFICATIONS MECHANICAL OPERATING TORQUE(1) BREAKOUT IMPACT HORIZONTAL MISCELLANOUS LEVER MECHANICAL ANGLE EXPECTED LIFE 1.1kg (without grip fitted) NOTES (1) The operating torque values are measured on-axis. (2) Loads are based on NH00 & NHFL grip options. The strength of the product will be limited by the grip/adaptor fitted to the joystick (NHA0 & NHAF are limited to 25Nm horizontal static loading). (3) One cycle is defined as moving from center to the end of travel, returning past the center to the other extreme and back to center. Joystick is cycled at a speed of 1Hz at an ambient temperature...

MAXIMUM SUPPLY CURRENT OUTPUT VOLTAGE RANGE (M) OUTPUT VOLTAGE RANGE (K) OUTPUT VOLTAGE RANGE (L) CENTER ACCURACY LINEARITY ACCURACY MATCHING ACCURACY OUTPUT IMPEDANCE CENTER REFERENCE OUTPUT CENTER REF. OUTPUT IMPEDANCE REVERSE POLARITY PROTECTION POWER-ON SETTLEMENT TIME INSULATION RESISTANCE @ 10VDC CLAMPING Two outputs per axis 10-90% of 5Vsupply 25-75% of 5Vsupply 20-80% of 5Vsupply ±4% supplied ±5.5% after life (including temperature effects) +2.8%/-4.5% of upper voltage +4.5%/-2.8% of lower voltage During the programming of the joystick the output at the ends of travel correspond to the...

SEALING'1' - ABOVE PANEL SEALING'2' - ELECTRONICS OPERATING TEMPERATURE 'CYCLING' TEMPERATURE & HUMIDITY SALT MIST SINUSOIDAL VIBRATION RANDOM VIBRATION BUMP SHOCK RADIATED EMISSIONS CONDUCTED DISTURBANCE IMMUNITY EN 61000-4-6 POWER FREQUENCY IMMUNITY EN 6100-4-8 Passes emissions levels of: '1' The overall sealing performance of the joystick is limited by the grip/boot fitted to the joystick. '2' The Molex connector is not rated.